Dichtomatik 75102054 O-Ring, 110 Dash Number, 0.362 in ID x 0.568 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102054
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter0.362 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter0.568 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75110
Recently Viewed
Dichtomatik 75102054 O-Ring, 110 Dash Number, 0.362 in ID x 0.568 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
HCI Preferred Supplier 6801NWO10 Elbow Connector, 7/8-14 Nominal, SAE Male JIC Flare x Male ORB, Steel
HCI Preferred Supplier 6801NWO10 Elbow Connector, 7/8-14 Nominal, SAE Male JIC Flare x Male ORB, Steel
Browning® 767392 VPLE 200 Normal Duty Pillow Block Ball Bearing, 2-7/16 in Dia Bore, 6-7/8 to 7-15/16 in L Bolt Center-to-Center, 2-11/16 in Base to Bore Centerline, 9-1/2 in OAL x 5-1/2 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
Browning® 767327 VPE 100 Intermediate Duty Pillow Block Ball Bearing, 2 in Dia Bore, 6-7/16 to 7-7/16 in L Bolt Center-to-Center, 2-1/2 in Base to Bore Centerline, 8-13/16 in OAL x 4-31/32 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
1/2" -HOSEX#8 FEMALE FLAT FACE 90-MHDE0808FF90 >
Appleton® UNILETS™ 8438R Ball Swivel Hanger Cover, 1/2 in, For Use With SHC Flexible Fixture Hanger, Malleable Iron/Steel
Appleton® UNILETS™ 8438R Ball Swivel Hanger Cover, 1/2 in, For Use With SHC Flexible Fixture Hanger, Malleable Iron/Steel
