Dichtomatik N70109 O-Ring, 109 Dash Number, 0.299 in ID x 0.505 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70109
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter0.299 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter0.505 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
Dichtomatik N70109 O-Ring, 109 Dash Number, 0.299 in ID x 0.505 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
2-3/16" -ID HIGH PILLOW BLOCK UNIT-MBUVPS235 >
4" BEIGE WALL BASE CORNER-M-D75374 >
The 1/4 in Collet Cone is designed for use with select Makita® die grinders. It is made of high quality materials for added durability. The 1/4 in collet accepts most die grinder accessories for grinding, sanding and polishing.
Gates® Power Transmission Synchro-Power® T5-575-12 Metric T Synchronous Belt, 12 mm W, 575 mm OAL, 5 mm Pitch, 115 Teeth, Polyurethane
Gates Synchro-Power™ polyurethane belts are designed for long-lasting and energy-efficient performance on both power transmission and linear applications. They are available in both endless and open-end versions in various sizes, constructions and tooth designs, handling a wide range of loads, speeds and applications.
MCR Safety TK132 Tomahawk® Single Lens Safety Glasses With Side Shields, Duramass® Hard Coat, Gray Lens, Wrap Around Frame, Blue/Red/White, Nylon Frame, Polycarbonate Lens, ANSI Z87+, AS/NZS 1337.1, CAN/CSA Z94.3, CE EN166
