Dichtomatik 75102015 O-Ring, 020 Dash Number, 0.864 in ID x 1.004 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102015
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter0.864 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter1.004 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75020
Recently Viewed
Dichtomatik 75102015 O-Ring, 020 Dash Number, 0.864 in ID x 1.004 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Browning® 767340 VPS 100 Intermediate Duty Pillow Block Ball Bearing, 1-3/8 in Dia Bore, 4-21/32 to 5-11/32 in L Bolt Center-to-Center, 1-7/8 in Base to Bore Centerline, 6-1/4 in OAL x 3-9/16 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
1/2" -HOSEX#10-ORFS FEMALE LONG90-MHDE0810FF90L >
DeWALT® 01205-PWR Long Shell Expansion Anchor, 1/2 in Dia, 2 in OAL, 3/4 in Drill, Zamac Alloy
The Lag Shield™ is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shield™ are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield™ is not recommended for overhead or life safety applications.
Browning® 767337 VPLE 100 Intermediate Duty Pillow Block Ball Bearing, 1-7/16 in Dia Bore, 4-9/16 to 5-7/16 in L Bolt Center-to-Center, 1-13/16 in Base to Bore Centerline, 6-3/4 in OAL x 3-5/8 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
DeWALT® 01201-PWR Short Shell Expansion Anchor, 1/2 in Dia, 2 in OAL, 3/4 in Drill, Zamac Alloy
The Lag Shield™ is a screw style anchor designed for use with lag bolts. It is suitable for use in concrete and the mortar joints of block or brick walls. In harder masonry materials, short style Lag Shield™ are used to reduce drilling time. The long style version is used in soft or weak masonry to better develop strength. The Lag Shield™ is not recommended for overhead or life safety applications.
