Dichtomatik N70404 O-Ring, 404 Dash Number, 1.85 in ID, Nitrile Rubber, 70 Shore A Durometer
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70404
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter1.85 in
-
Durometer70 Shore A
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Package DescriptionEACH
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Dichtomatik N70404 O-Ring, 404 Dash Number, 1.85 in ID, Nitrile Rubber, 70 Shore A Durometer
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
ISOSTATICā¢ OilubeĀ® 401236 Round Bore Sleeve Bearing, 3/4 in Dia Bore, 15/16 in OD, 7/8 in W
ISOSTATICā¢ OilubeĀ® 401236 Round Bore Sleeve Bearing, 3/4 in Dia Bore, 15/16 in OD, 7/8 in W
StarrettĀ® 78XTZ-750 78XT Global SeriesĀ® Mechanical Bore Gage, 5/8 to 3/4 in, Graduations: 0.00025 in, 2-7/16 in D Probe, Tungsten Carbide
The Starrett 78XT Series Internal Micrometer features extended travel, reducing the need to exchange anvils. The ground contact points seat the internal micrometer faster and more accurately than the spherical contacts found in other gages. The rugged and accurate internal micrometer is available individually or in economical sets from .040-12" (1-300mm). 5/8-3/4" Range, w/3 Point Carbide Contact.
MakitaĀ® 792534-4 Center Blade, For Use With MakitaĀ® DJS161 Straight Shear
MakitaĀ® 792534-4 Center Blade, For Use With MakitaĀ® DJS161 Straight Shear
The LittelfuseĀ® LGR and LMF series fuses and LHR holder offer increased safety and reliability to lighting systems. on a 277 volt system, a fault occurring in an un-fused fixture could take out the entire branch circuit affecting upto 100 fixtures. this could cause safety problems as well as shut down operations. by individually fusing fixtures, these problems will be avoided. The added benefits of this is the ability to quickly identify the problem fixture and reduce the repair time. fuse holders are rated upto 10 A at 300 V and are equipped with 7 18 AWG leads. Order part number LHR 000 for two leads and part number LHR 001 for one lead and one terminal for insertion of 18 AWG ballast lead.
ISOSTATICā¢ OilubeĀ® 401177 Round Bore Sleeve Bearing, 9/16 in Dia Bore, 13/16 in OD, 1 in W
ISOSTATICā¢ OilubeĀ® 401177 Round Bore Sleeve Bearing, 9/16 in Dia Bore, 13/16 in OD, 1 in W
