BBI 042016 Partially Threaded Cap Screw, 1/4-20, 1-3/4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
BBI 042016 Partially Threaded Cap Screw, 1/4-20, 1-3/4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
-
BrandBBI
-
UPC662403339059
-
Manufacturer Part Number042016
-
CountryUSA
-
FinishZinc Yellow Bake CR+6
-
Tensile Strength150000 psi
-
MaterialAlloy Steel
-
Material SpecificationASTM B633-Fe, Zn5 Type 2
-
Thread TypeUNC
-
Measurement SystemImperial
-
TypePartially Threaded
-
Grade8
-
Hardness33 to 39 HRC
-
Head Size5/32 in H
-
Head TypeHex
-
Shank Size1/4 in
-
Diameter - Thread Size1/4-20
-
Length Under Head1-3/4 in
-
UNSPSC31161501
-
Package Description100/CS
-
Standards/ApprovalsASME/ANSI B18.2.1
Recently Viewed
BBI 042016 Partially Threaded Cap Screw, 1/4-20, 1-3/4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
BBI 042016 Partially Threaded Cap Screw, 1/4-20, 1-3/4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
Dichtomatik N70202 O-Ring, 202 Dash Number, 0.234 in ID x 0.512 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
72 14/3" AIR CONDITIONER & MAJOR APPLIANCE CORD-ECI03532 >
Dichtomatik N70142 O-Ring, 142 Dash Number, 2.362 in ID x 2.568 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
ISOSTATIC™ Century® 104035 Round Bore Sleeve Bearing, 3/8 in Dia Bore, 5/8 in OD, 1 in W
ISOSTATIC™ Century® 104035 Round Bore Sleeve Bearing, 3/8 in Dia Bore, 5/8 in OD, 1 in W
Browning® 1296367 T35L Automatic Torque Limiter, 5/8 in Finished Bore, 3-1/2 in OD, 1800 in-lb (1-Spring)/3000 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
