BBI 455704 Partially Threaded Cap Screw, 1-14, 4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
BBI 455704 Partially Threaded Cap Screw, 1-14, 4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
-
BrandBBI
-
Manufacturer Part Number455704
-
CountryUSA|Canada
-
FinishZinc Yellow Bake CR+6
-
Tensile Strength150000 psi
-
MaterialAlloy Steel
-
Material SpecificationASTM B633-Fe, Zn5 Type 2
-
Thread TypeUNF
-
Measurement SystemImperial
-
TypePartially Threaded
-
Grade8
-
Hardness33 to 39 HRC
-
Head Size39/64 in H
-
Head TypeHex
-
Shank Size1 in
-
Diameter - Thread Size1-14
-
Length Under Head4 in
-
UNSPSC31161501
-
Package Description10/CS
-
Standards/ApprovalsASME/ANSI B18.2.1
Recently Viewed
BBI 455704 Partially Threaded Cap Screw, 1-14, 4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
BBI 455704 Partially Threaded Cap Screw, 1-14, 4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
BBI 455372 Fully Threaded Cap Screw, 9/16-12, 1-1/4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
BBI 455372 Fully Threaded Cap Screw, 9/16-12, 1-1/4 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
36" UV BLACK CABLE TIE-175#--PACK OF 50-CTE36175UV50 >
Proto® J278G Combination Slip Joint Plier, 1-3/4 in L x 1-13/64 in W x 3/8 in THK Forged Alloy Steel Jaw, Serrated Jaw Surface, 8-1/16 in OAL, ASME B107.23
Browning® 1296516 T55L Automatic Torque Limiter, 1-1/4 in Finished Bore, 5-1/2 in OD, 3800 in-lb (1-Spring)/6800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
JASON BX68 COGGED CLASSICAL V-BELTS. 21/32 " TOP WIDTH, 13/32 " THICK
RAW EDGE COGGED V-BELT; 21/32 WIDTH, 71" BELT OUTSIDE LENGTH, 1 BAND, POLYESTER TENSILE MATERIAL, RUBBER OUTER MATERIAL.
-JASBX68 >
