Hollow Wall & Wallboard Anchors
POWERS ZINC ZIP-ITS W/SCREWS PWR 2349-Z
The Zip-It® anchor is a one piece self-drilling anchor designed for use in hollow gypsum wallboard for light to medium duty loads. It is available in both engineered nylon and Zamac alloy for use with NO 8 screws in 3/8 to 1 in thick wallboard. The Zip-It Jr. is also available in engineered nylon and Zamac alloy for use with NO 6 screws in 3/8 to 5/8 in wallboard.
The Zip-It® anchor is a 1-piece self drilling anchor designed for use in gypsum wallboard for light to medium duty loads. It is available in both engineered nylon and Zamac alloy designed for use with No. 8 screws in 3/8 to 1 in THK wallboard. The Zip-It® Jr. is also available in engineered nylon and Zamac alloy designed for use with No. 6 screws in 3/8 to 5/8 in THK wallboard. These fasteners are not recommended for use overhead or applications where holding values are critical.
Pop-Toggle™ fasteners are Hollow Wall Anchors ideal for static applications requiring light to medium load performance. The fastener pre-installs without a screw, allowing for easy placement and removal of the fixture. These fasteners are not recommended for use overhead or applications where holding values are critical.
The Zip-It® anchor is a one-piece self-drilling anchor designed for use in hollow gypsum wallboard for light duty loads. It is available in both engineered nylon and Zamac alloy for use with either a no. 6 or no. 8 screws in 3/8 in to 1 in wallboard. The Zip-It® Jr. Is formed from engineered nylon for use with no. 6 screws in 3/8 in to 5/8 in wallboard.
The Polly™ is a sleeve type Hollow Wall Anchor designed for use in base materials such as plaster, wallboard or hollow tile. Once the anchor has been set, the screw may be removed as often as necessary without affecting the Anchor.
The Zip-It anchor is a one-piece self drilling anchor designed for use in hollow gypsum wallboard for light to medium duty loads. It is available in both engineered nylon and Zamac alloy for use with No. 8 screws in 3/8" to 1" thick wallboard. The Zip-It Jr. is also available in engineered nylon and Zamac alloy for use with No. 6 screws in 3/8" to 5/8" wallboard.
Recently Viewed
Waterproofing 3Lb Waterproof Hydraulic Cement Hydraulic Repair 07032
Proto® JSF20M Surface Protective Hammer Tip, 2 in Plastic Tip, Medium, Red
MORSE® 25583 1752 Countersink, 5/8 in Dia Body, 1/2 in Dia Shank, 1 Flutes, 60 deg Included, HSS
Proto® TorquePlus™ J6907M Standard Length Socket, Metric, 1/4 in Square Drive, 7 mm
Irwin® Unibit® 10310 Self-Starting Step Drill Set, 1/2 in Dia Min Hole, 1 Steps, 1 Hole Sizes, 1/4 in Shank
Irwin® Unibit® step drill bits are ideal for drilling holes in just about any type of thin material. General purpose high speed steel Unibit® step drill bits are perfect for use in mild steel, copper, brass, aluminum, plexiglass, wood, and laminate. Our titanium nitride coated (TiN) bits resist heat and friction, which extends the life of the cutting edge six times longer than standard step drills. And, our cobalt step drill bits are engineered with m35 cobalt steel for maximum life when drilling in the toughest steel, including stainless steel. Most Unibit® step drills are designed with a SpeedPoint® tip that guarantees fast starts. Theyre manufactured with a single flute cutting edge that drills multiple sizes of true, round holes with precise step control. Plus, the hole sizes are permanently laser etched on the inside of the flute, so they can be easily identified throughout the life of the bit.
5/32"-ID 9/32"-OD SILICONE O-RINGS
