ACCESSORIES
1-1/4" ALUMINUM ENTRANCE HEAD-APLECO103 >
1-1/2" ALUMINUM ENTRANCE HEAD-APLECO104 >
2.5" ALUMINUM ENTRANCE HEAD-APLECO106 >
3" ALUMINUM ENTRANCE HEAD-APLECO107 >
1" UNILET NEOPRENE GASKETS-APLGK100N >
2" UNILET NEOPRENE GASKETS-APLGK200N >
2-1/2" UNILET NEOPRENE GASKETS-APLGK250300N >
1/2" UNILET NEOPRENE GASKETS-APLGK50N >
1/2" INSULATED ELECTRICAL CONNECTOR-ELEIL121 >
1/2" INSULATED THROAT ELECTRICAL NIPPLE-ELEIL701 >
3/4" -MALE PIPE THREAD INSULATED THROAT NIPPLE-ELEIL702 >
3-1/2"-4" UNILET ALUMINUM COVERS-APLK350400A>
3-PC 1" KNOCKOUT SEALS-ELEKOS100>
1-1/4" 3-PC KNOCKOUT SEAL-ELEKOS125>
3-PC 3/4" KNOCKOUT SEALS-ELEKOS705>
1/2" ALUMINUM THREADED LL UNILETS-ELEL1001 >
1" ALUMINUM THREADED LL UNILETS-ELEL1003 >
3/4" ALUMINUM THREADED C UNILETS-ELEL1012 >
1" ALUMINUM THREADED C UNILETS-ELEL1013 >
1-1/2" ALUMINUM THREADED C UNILETS-ELEL1015 >
1/2" UNILET ALUMINUM COVER-ELEL1021 >
3/4" UNILET ALUMINUM COVER - ELEL1022 >
1" UNILET ALUMINUM COVER-ELEL1023 >
1-1/4" /1-1/2" UNILET ALUMINUM COVER-ELEL1024 >
Recently Viewed
metabo® 676116000 2-Cutter Hammer Drill Bit, 1/2 in Drill Bit, Spline Shank, 11 in D Cutting, Carbide Cutting Edge, 16 in OAL
Browning 60-TOOTH #160-1 CHAIN TL SPROCKETS BRW 160-TB-60
Browning® offers a variety of bushing type sprockets available in single and double strands. Offerings include 35 to 160 pitch range. Bushed type bore ranges are available from 1/2 to 5 in. Hardened teeth are available up to 30 teeth.
Browning® 1078054 QD Bushing, 2-3/8 in Dia Bore, 2-13/16 in Dia Barrel, 3-7/8 in Dia Flange, 1-3/4 in OAL, Ductile Iron
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
Anvil® 0318905486 FIG 383 Hex Head Pipe Bushing, 1/2 x 3/8 in Nominal, MNPT x FNPT End Style, 150/300 lb, Cast Iron, Black Oxide, Domestic
Anvil International offers the broadest line of malleable iron fitting sizes in both black and galvanized finishes. Every fitting is manufactured and tested to meet Anvil's strict quality standards. All Anvil Class 150/300 Malleable Iron Fittings conform to ASME B16.3 and unions conform to ASME B16.39. All elbows and tees 3/8 in (10 DN) and larger are 100% gas tested at a minimum of 100 PSI (6.9 bar).
Proto® J1280M Combination Wrench, Metric, 80 mm, 12 Points, 15 deg Offset, 34 in OAL, Alloy Steel, Black Oxide, ASME B107.100
Apex® SZ-7-12MM Socket Head Insert Bit, 12 mm Hex Point, 1-3/8 in OAL, Steel
