ACCESSORIES
3-1/2" STAINLESS STEEL RIGID CONDUIT CLAMPS-BLNB2016SS4 >
3" STAINLESS STEEL RIGID CONDUIT CLAMPS-BLNB2015SS4 >
3" PIPE, CONDUIT, & TUBING CLAMPS-BLNB2015 >
2-1/2" STAINLESS STEEL RIGID CONDUIT CLAMPS-BLNB2014SS4 >
2-1/2" PIPE OR RIGID CONDUIT CLAMP-BLNB2014 >
2" STAINLESS STEEL RIGID CONDUIT CLAMPS-BLNB2013SS4 >
1-1/4" STAINLESS STEEL RIGID CONDUIT CLAMPS-BLNB2011SS4 >
APPLETON CONDUIT CONNECTOR, LIQUID TIGHT OILTIGHT RAINTIGHT, SERIES: ST SERIES, 3/4". 90 DEG, FOR USE WITH: LIQUID TIGHT FLEXIBLE METALLIC CONDUIT, MALLEABLE IRON, TRIPLE COATED, 1-1/2" W
-APLST9075 >
APPLETON S50, 1/2" SNAP-IN KNOCKOUT BLANK, STEEL. FOR USE TO CLOSE A KNOCKOUT OR SLIPHOLE IN A SHEET METAL ENCLOSURE
-APLS50 >
S-125 KNOCKOUT BLANK, 1-1/4", FOR USE WITH IMC/RIGID CONDUIT FITTINGS, STEEL
-APLS125 >
1" X 3/4" CUPPED REDUCING CONDUIT WASHER - STEEL-APLRW10075 >
FORM 35 GASKET, TRADE SIZE: 1-1/4, 1-1/2", MATERIAL: NEOPRENE, STANDARD: UL 514A AND 514B. FOR USE WITH RIGID STEEL, RIGID ALUMINUM, IMC, AND EMT CONDUIT.
-APLGK125150N >
EATON, OUTLET BOX AND COVER CONDUIT AND FITTING
-APLGK75N >
APPLETON GK-350-400N MALLEABLE IRON UNILET COVER GASKET, BODY SIZE: 3-1/2 4", NMATERIAL: NEOPRENE
NEOPRENE FORM 35, 3-1/2 TO 4", SUITABLE FOR RIGID STEEL, RIGID ALUMINUM WITH IMC AND EMT CONDUIT
-APLGK350400N>
FEATURES: 6.9" D X 5.75" H, (2) 3/4", (3) 1", (1) 1-5/16" HOLES, WEATHER RESISTANT, FOR THREADED/UNTHREADED RIGID CONDUIT, IMC/EMT SERVICE MASTS,
-APLECO105 >
16-OZ CONDUIT SEALING CEMENT-APLAC1A >
1/2" & 3/4" CONDUIT BENDER HANDLE-GRN845>
SQUARE ELECTRICAL COVER-ELE572BC>
1/2" GROUNDING ROD CLAMP - JWH554979>
1" LIQUIDTITE STRAIGHT CONNECTOR-ELE5234TB >
81_100x100.jpg)
3/8" NUT CHAIN NYLON-JWH514136>
1/4" SUPERSTRUT CHANNEL CONE NUT/PK-JWH513806>
1/2 NUT, CHAIN NYLON-JWH512982>
5/8" GROUND ROD CLAMP SILICONE BRONZE CONSTRUCTION, MAXIMUM SERVICE AND CONDUCTIVITY. LISTED FOR DIRECT BURIAL
- JWH510496 >
Recently Viewed
1-1/2" EMT COMPRESSION CONNECTOR-ELEL29 >
MORSE® 32702 2046 Straight Flute Hand Tap Set, Right Hand Cutting, Bottoming/Plug/Taper Chamfer, H3 Thread Limit
#3 KEYED ALIKE #3488 PADLOCK - MAS3KA3488 >
Milwaukee® 48-20-5045 Heavy Duty Thin Wall Core Bit, 3 in Drill - Fraction, 3 in Drill - Decimal Inch
Milwaukee's core bits are ideal for large hole drilling where depth is relatively shallow. The core bit cuts a Kerf only. The usable depth of thick wall core bits is 4-3/8 in. The inside core must be removed by the operator before deeper drilling can be accomplished. The thick wall construction is ideal for larger hammers and more seasoned/cured concrete. A 7-1/2 in. extension is available to allow for the deeper holes to be drilled. The appropriate (Dependant on the diameter) SDS Plus drive shank must be used to drive the core bit. Use 48-20-6155 center pin and 48-20-6159 guide plate for positioning and starting the hole. Thin wall core bits are available from 1 in. to 6 in. diameters. See thick wall core bits for cured concrete and/or larger hammers.
Dodge® 065296 215 Special Duty Type C Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 11.13 to 12.38 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 14-1/4 in OAL x 9.88 in OAH
Dodge® 065296 215 Special Duty Type C Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 11.13 to 12.38 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 14-1/4 in OAL x 9.88 in OAH
Krylon® Tough Coat® A00340 S003 Rust Control Solvent Based Spray Primer, 16 oz Container, Liquid Form, Gray, 20 sq-ft Coverage
