Roughing & Finishing End Mills
MORSE® 43425 1896 Center Cutting Double End Regular Length End Mill, 9/16 in Dia Cutter, 1-1/8 in Length of Cut, 2 Flutes, 5/8 in Dia Shank, 5 in OAL, Bright
MORSE® 58018 5944 Center Cutting Regular Length Single End End Mill, 9/32 in Dia Cutter, 3/4 in Length of Cut, 2 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, Bright
MORSE® 43417 1896 Center Cutting Double End Regular Length End Mill, 9/32 in Dia Cutter, 9/16 in Length of Cut, 2 Flutes, 3/8 in Dia Shank, 3-1/8 in OAL, Bright
MORSE® 44565 4581 Center Cutting Double End Regular Length End Mill, 9/32 in Dia Cutter, 9/16 in Length of Cut, 2 Flutes, 3/8 in Dia Shank, 3-1/8 in OAL, Bright
MORSE® 90790 5943T Center Cutting Regular Length Single End End Mill, 9/32 in Dia Cutter, 3/4 in Length of Cut, 4 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, TiAlN Coated
MORSE® 90716 5943G Center Cutting Regular Length Single End End Mill, 9/32 in Dia Cutter, 3/4 in Length of Cut, 4 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, TiN Coated
MORSE® 43271 1895 Double End Non-Center Cutting Regular Length End Mill, 9/32 in Dia Cutter, 11/16 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3-3/8 in OAL, Bright
MORSE® 57918 5943 Center Cutting Regular Length Single End End Mill, 9/32 in Dia Cutter, 3/4 in Length of Cut, 4 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, Bright
MORSE® 44585 4582 Center Cutting Double End Regular Length End Mill, 9/32 in Dia Cutter, 11/16 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3-3/8 in OAL, Bright
MORSE® 43431 1896 Center Cutting Double End Regular Length End Mill, 9/64 in Dia Cutter, 7/16 in Length of Cut, 2 Flutes, 3/8 in Dia Shank, 3-1/8 in OAL, Bright
MORSE® 57909 5943 Center Cutting Regular Length Single End End Mill, 9/64 in Dia Cutter, 9/16 in Length of Cut, 4 Flutes, 3/16 in Dia Shank, 2 in OAL, Bright
MORSE® 90819 5943T Center Cutting Regular Length Single End Mill, 11/32 in Dia Cutter, 1 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 2-1/2 in OAL, AlTiN Coated
Recently Viewed
Channellock® 337 High Leverage Diagonal Cutting Plier, 0.06 to 0.09 in Piano Wire, 0.04 to 0.09 in Hard Wire, 0.04 to 0.09 in Medium Hard Wire, 0.16 in Soft Wire Nominal, 0.79 in L x 1.18 in W x 0.43 in THK C1080 High Carbon Steel Lap Joint/Oval Jaw
Not all cutting edges are the same. Only Channellock® uses precision machined knife and anvil style cutting edges to ensure perfect mating and superior cutting edge life. The Channellock® knife and anvil cutters ensure proper cutting edge alignment, resulting in a clean cut every time. Most manufacturers use two sharp edges which can become misaligned, losing their cutting effectiveness. Experience the difference for yourself.
TB Wood's® L1501 Straight L-Jaw Coupling Hub, L150 Coupling, 1 in Bore, 1-3/4 in, 3-3/4 in Hub, Sintered Carbon Steel
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
2" -MALE PIPE THREADX1-1/4" -FEMALE PIPE THREAD HYDRAULIC BUSHING-DAY54063220 >
SINGLE GROOVE A-BELT 5/8" -ID SHEAVES-BRWAK51X5/8 >
Browning® 1077452 QD Bushing, 2-9/16 in Dia Bore, 3-1/8 in Dia Barrel, 4-5/8 in Dia Flange, 1.995 in OAL, Ductile Iron
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
