Drillco 72A132C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/2 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 1/2 in Dia Shank, 3 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
-
BrandDrillco
-
UPC045997390192
-
Manufacturer Part Number72A132C
-
CountryUSA|Canada
-
FinishUncoated
-
MaterialSolid Carbide
-
Flute TypeSpiral
-
TypeCenter Cutting Imperial Regular Length Single End
-
Helix Angle30 deg
-
Series7200
-
Cutter Diameter1/2 in
-
Shank Diameter1/2 in
-
Number of Flutes2
-
Cutting DirectionRight Hand
-
Shank TypeRound
-
Length of Cut1 in
-
Overall Length3 in
- Solid carbide construction for extreme rigidity and strength
- Center cutting tip for plunging, pocketing and holemaking
- Solid carbide can be ran at 3x the speed and feed of HSS
- 2 flutes provide more efficient chip removal
- Bright finish for added lubricity
-
UNSPSC27112803
-
Package Description1/PK
-
Standards/ApprovalsPROP65: This product can expose you to chemicals including Cobalt, which is [are] known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
-
SDS
-
Catalog
Recently Viewed
Drillco 72A132C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/2 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 1/2 in Dia Shank, 3 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Drillco 670A132B 6700A Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/2 in Dia Cutter, 1-1/4 in Length of Cut, 4 Flutes, 1/2 in Dia Shank, 3-1/4 in OAL, Uncoated
The greater red hardness of M-42 Cobalt end mills enables these tools to run about 10% faster than conventional HSS end mills. This translates to shorter machining times and permits higher utilization of available machine horsepower.
Permatex® 80008 Form-A-Gasket® #1 No.1 Fast Dry Rigid Cure Gasket Sealant, 3 oz Container Tube Container
Permatex® Form-A-Gasket® No. 1 Sealant is a reddish brown, viscous paste with a characteristic alcoholic odor. It is a fast drying paste that changes to a hard, semi flexible seal through solvent evaporation. It seals flanges, fittings, connections and assembles against leakage. Improves gasket seal in permanent and rigid assemblies.
Drillco 51A216E 5100A Imperial Multi-Flute Non-Center Cutting Regular Length Single End Finishing End Mill, 1-1/4 in Dia Cutter, 2 in Length of Cut, 6 Flutes, 7/8 in Dia Shank, 4-1/2 in OAL, Uncoated
The multi-flute end mill has a better finishing capability than a 2-flute end mill. At any given instance, at least one and often two of the teeth are solidly in the cut. The cutting action is smoother than that of the 2-flute end mill, with less chatter.
The MILWAUKEE® Full Brim Vented Hard Hats with 4-Point Ratcheting Suspension - Type 1, Class C are designed to adapt to your jobsite. Four BOLT™ accessory slots and two universal accessory slots easily integrate additional personal protection equipment and accessories onto the hard hat. All MILWAUKEE® hard hats have a ratcheting suspension for quick adjustment and added comfort. A sweatband is included and is moisture-wicking for additional comfort. These construction hard hats are ANSI/CSA approved and can be customized by adding your logo.
50-B-50-F-1-3/4 50 Tooth Sprockets For #50
50 TOOTH SPROCKETS FOR #50 CHAIN-IDC50B50F13/4 >


