Hougen® Rotabroach® 3-12228 12000 Annular Cutter, 7/8 in Dia Cutter, 3 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
-
BrandHougen®
-
UPC662850006061
-
Manufacturer Part Number3-12228
-
CountryUSA
-
FinishBright
-
MaterialM2 HSS
-
Applicable MaterialsMild Steel, Structural Steel, Aluminum, Stainless Steel, Ferrous and Non-Ferrous Materials
-
Series12000
-
Cutter Diameter7/8 in
-
Cutting Depth3 in
-
Shank Size3/4 in
-
Shank TypeWeldon with 2-Flat
- Ground and fully fluted - Provides better chip evacuation, requires less hp and offers better performance in deeper holes
- Two flats for cutter mounting - This system is very rigid and offers up to 2x the tool life as compared to quick change tool mounting on competitive products
- OD Margin - Only a thin area of material touches the outside of the hole which provides for less friction and a better hole finish
- ID Taper - Relief area between slug and cutter
- The Hougen-Edge® feature is a patented tooth geometry that provides long tool life, less chatter and extended resharpenability
- The slug also offers a higher scrap value than loose chips
- For use with 24131 pilot
- For use with Hougen® portable magnetic drills and many competitive models on materials up to 6 in thick
- They are made from hardened M2 high speed steel and are precision-ground for excellent performance throughout the cut and long tool life
| Competitor Name | Competitor Part Number |
|---|---|
| Grainger | 45RG65 |
-
UNSPSC23241600
-
Catalog
-
Owners/User Manual
Recently Viewed
Hougen® Rotabroach® 3-12228 12000 Annular Cutter, 7/8 in Dia Cutter, 3 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
MARXMAN™ 85005 330QI General Purpose Jobber Length Drill Bit, 9/64 in Drill - Fraction, 0.1406 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MARXMAN™ 85005 330QI General Purpose Jobber Length Drill Bit, 9/64 in Drill - Fraction, 0.1406 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
4-1/2" X 7/8" 120-GRIT TYPE 29 FLAP DISC, BLUE ZIRCONIA, DEPRESSED CENTER-FOR71988 >
National Hardware® N102-855 V32 Swivel Staple Safety Hasp With Pin, 3-1/4 in L x 1-1/2 in W, 0.07 in THK, Hot Rolled Steel/Aluminum
McKissick® 109037 419 Light Champion Snatch Block With Shackle, Wire Rope Cable, 5/16 to 3/8 in, 2 ton Load, 3 in OD
McKissick® 109037 419 Light Champion Snatch Block With Shackle, Wire Rope Cable, 5/16 to 3/8 in, 2 ton Load, 3 in OD
MORSE® 11360 1340 General Purpose Jobber Length Drill Bit, #72 Drill - Wire, 0.025 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 11360 1340 General Purpose Jobber Length Drill Bit, #72 Drill - Wire, 0.025 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
