Hougen 1-3/4" X 1"-DEPTH METAL CUTTERS HOU 12156
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
-
BrandHougen®
-
UPC662850002506
-
Manufacturer Part Number12156
-
CountryUSA
-
FinishBright
-
MaterialM2 HSS
-
Applicable MaterialsMild Steel, Structural Steel, Aluminum, Stainless Steel, Ferrous and Non-Ferrous Materials
-
Cutter Diameter1-3/4 in
-
Cutting Depth1 in
- Ground and fully fluted - Provides better chip evacuation, requires less hp and offers better performance in deeper holes
- Two flats for cutter mounting - This system is very rigid and offers up to 2x the tool life as compared to quick change tool mounting on competitive products
- OD Margin - Only a thin area of material touches the outside of the hole which provides for less friction and a better hole finish
- ID Taper - Relief area between slug and cutter
- The Hougen-Edge® feature is a patented tooth geometry that provides long tool life, less chatter and extended resharpenability
- The slug also offers a higher scrap value than loose chips
- For use with 10527 pilot
- For use with Hougen® portable magnetic drills and many competitive models on materials up to 6 in thick
- They are made from hardened M2 high speed steel and are precision-ground for excellent performance throughout the cut and long tool life
| Competitor Name | Cross-Reference Number |
|---|---|
| Berkshire eSupply | FZ8012156 |
-
UNSPSC23241600
-
Catalog
-
Owners/User Manual
Recently Viewed
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
Gardner Bender PPC-1538 Fast Install Smooth Edge Cable Clamp, 3/8 in Conduit, Plastic
Gardner Bender plastic clamps are tough, durable, yet extremely lightweight and feature clean, smooth edges to minimize damage to cables. Our contractor-friendly design facilitates quick installations saving time and money. Clamps securely hold harnesses, cables and tubing up to 3/8 in diameter. Designed for use in construction, maintenance and assembly-line applications, control cabinets, panels and general applications. Choose these clamps for superior performance indoors. Working temperature range: -54 C (-66 F) to 170 C (340 F) Instructions: position clamp at desired location, insert cable(s) or tube(s), fasten with screw or nail.
Irwin® Vise-Grip® Original™ 4935578 Locking Plier, 1-1/2 in Nominal, Classic Trigger Locking, Alloy Steel Curved Jaw, 7 in OAL
Irwin® Vise-Grip® Original™ 4935578 Locking Plier, 1-1/2 in Nominal, Classic Trigger Locking, Alloy Steel Curved Jaw, 7 in OAL
Dixon® KRW20 Coupling Gasket, 1-1/2 in Nominal, 1-5/16 in ID x 1-15/16 in OD x 1/8 in THK, Rubber, Domestic
Dixon® KRW20 Coupling Gasket, 1-1/2 in Nominal, 1-5/16 in ID x 1-15/16 in OD x 1/8 in THK, Rubber, Domestic
#8 X 5/8" Hex Head Slotted Sheet Metal Screws With Washer
Browning® 1212273 Minimum Plain Bore Spur Gear, 8 Diametral Pitch, 14.5 deg, 1-1/4 in W Face, 12 Teeth, 1-1/2 in Dia Pitch, 3/4 in Dia Bore, Steel
Browning® offers a comprehensive line of off-the-shelf gears, including spur, miter, bevel and change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14-1/2 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
