MORSE C/Tool 7/16" CARBIDE-TIPPED DIE DRILLBITS MCT 52128
MORSE® 52128 5423 Standard Length Spade Drill, 7/16 in Drill - Fraction, 0.4375 in Drill - Decimal Inch, 3 in D Cutting, 2 Flutes
-
BrandMORSE®
-
UPC686125521288
-
Manufacturer Part Number52128
-
CountryUSA
-
FinishBright
-
Point Angle118 deg
-
Point TypeStandard
-
Flute Length3 in
-
Flute TypeStraight
-
TypeStandard Length
-
Applicable MaterialsHardened Steel
-
Series5423
-
Number of Flutes2
-
Cutting Depth3 in
-
Shank Size25/64 in
-
Cutting DirectionRight Hand
-
Cutting Edge MaterialCarbide Tipped
-
Shank TypeStraight
-
Drill Diameter Measurement SystemImperial
-
Drill Size - Decimal Inch0.4375 in
-
Drill Size - Fraction7/16 in
-
Overall Length5-1/2 in
- Drilling hardened steel of 35 to 65 HRC without the need to anneal the workpiece
- Drill body diameter is smaller than tip diameter to prevent galling
-
UNSPSC23241605
-
Package Description1/PK
-
Standards/ApprovalsISO 9001:2008
Recently Viewed
MORSE® 52128 5423 Standard Length Spade Drill, 7/16 in Drill - Fraction, 0.4375 in Drill - Decimal Inch, 3 in D Cutting, 2 Flutes
RIDGID® 37890 Manual Threader Pipe Die, 1-1/2 in Conduit/Pipe, 1-1/2-11-1/2 NPT Thread, Right Thread, 4 Pieces, For Use With OO-R, 11-R, 12-R, O-R, Ratchet Threaders and 30A, 31A 3-Way Pipe Threaders, HSS
RIDGID® 37890 Manual Threader Pipe Die, 1-1/2 in Conduit/Pipe, 1-1/2-11-1/2 NPT Thread, Right Thread, 4 Pieces, For Use With OO-R, 11-R, 12-R, O-R, Ratchet Threaders and 30A, 31A 3-Way Pipe Threaders, HSS
MODULAR CABINET DRAWER DIVIDERS-STSD3007>
GENERAL® 1280ST Hollow Punch Set, 3/16 in, 1/4 in, 5/16 in, 3/8 in, 7/16 in and 1/2 in Punch, 6 Punches, 6 Pieces
The #1280ST 6-piece hollow steel punch set is ideal for punching round holes in gasket material, leather, rubber, canvas, cardboard, plastic, sheet metal and other soft materials.
1-GAL SAE-40 SHELL ROTELLA OIL-SHL56036 >
Gates® Power Transmission MegaCrimp™ 6G-8MPX G25 Straight Hydraulic Coupling, 3/8 in x 1/2-14 Nominal, Hose x MNPTF Swivel, Steel
It’s what’s inside the MegaCrimp coupling that makes it perform so well, the “C” insert. This “C” insert allows usage with different hose constructions and wall thicknesses. In addition, the C-insert ensures an even distribution of crimping forces to form a concentric seal. That simplifies your inventory requirements since one size can accommodate many different hose ODs, on both one- and two-wire braid hoses and select Xpiral hoses. An additional bonus: MegaCrimp couplings are fully qualified for SAE, EN, and ISO performance.
