MORSE C/Tool #7 COBALT JOBBERS DRILLBITS MCT 17164
MORSE® 17164 2340 1-Stage Type J Heavy Duty Jobber Length Aircraft Drill, #7 Drill - Wire, 0.201 in Drill - Decimal Inch, 135 deg Point, Cobalt
-
BrandMORSE®
-
UPC686125171643
-
Manufacturer Part Number17164
-
CountryUSA
-
FinishStraw Oxide
-
Point Angle135 deg
-
Point TypeSplit
-
MaterialCobalt
-
Flute Length2-7/16 in
-
Flute TypeStandard
-
Type1-Stage Type J Heavy Duty Jobber Length
-
Applicable MaterialsHigh Alloy Steel, Ferrous Casting, Titanium, Inconel and Stainless Steel
-
Series2340
-
Cutting Depth2-7/16 in
-
Cutting DirectionRight Hand
-
Cutting Edge MaterialCobalt
-
Shank TypeStraight
-
Drill Size - Decimal Inch0.201 in
-
Drill Size - Wire#7
-
Overall Length3-5/8 in
- Cobalt steel offers increased hardness, toughness, wear resistance and heat-resistance
- Recommended for drilling tough, high tensile strength materials that generate higher cutting temperatures including high alloy steels, ferrous castings, titanium, inconel, stainless steel sand other difficult-to-drill materia
| Competitor Name | Competitor Part Number |
|---|---|
| Berkshire eSupply | MT1117164 |
-
UNSPSC23241606
-
Package Description1/PK
-
Standards/ApprovalsNAS-907
Recently Viewed
MORSE® 17164 2340 1-Stage Type J Heavy Duty Jobber Length Aircraft Drill, #7 Drill - Wire, 0.201 in Drill - Decimal Inch, 135 deg Point, Cobalt
7/16" -14" X 72 USS ZINC THREADED ROD-NBS9930440600 >
Milwaukee® 48-20-5150 Heavy Duty Thick Wall Core Bit, 3-1/2 in Drill - Fraction, 3.5 in Drill - Decimal Inch, Carbide
Milwaukee's core bits are ideal for large hole drilling where depth is relatively shallow. The core bit cuts a Kerf only. The usable depth of thick wall core bits is 4-3/8 in.. the inside core must be removed by the operator before deeper drilling can be accomplished. The thick wall construction is ideal for larger hammers and more seasoned/cured concrete. A 7-1/2 in. extension is available to allow for the deeper holes to be drilled. The appropriate (Dependant on the diameter) Spline drive shank must be used to drive the core bit. Use 48-20-5199 center pin and 48-20-5173 guide plate for positioning and starting the hole. Thick wall core bits are available from 1 in. to 6 in. diameters. See thin wall core bits for less expensive drilling in new concrete and/or smaller hammers.
3-PC 3/8"-DR EXTENSION SETS - ALL11921 >
RIDGID® 38365 Bolt Threader Button Die, 5/8 in Conduit/Pipe, 5/8-11 UNC Thread, Right Thread, For Use With OO-RB Ratchet Bolt Threaders or 31B, 33B, 35B and 37B 3-Way Bolt Threaders, Alloy Steel
RIDGID® 38365 Bolt Threader Button Die, 5/8 in Conduit/Pipe, 5/8-11 UNC Thread, Right Thread, For Use With OO-RB Ratchet Bolt Threaders or 31B, 33B, 35B and 37B 3-Way Bolt Threaders, Alloy Steel
Milwaukee® 48-20-6774 4-Cutter Rebar Cutter, 1/2 in Drill Bit, 0.5 in Shank 3-Flat Shank, 10 in D Cutting, 8 in OAL
The MILWAUKEE® Straight Shank Rebar Cutters are the toughest in rebar, delivering up to 3x life in rebar compared to competitive rebar cutters. These bits, designed with precision ground carbide for rebar only drilling, provide up to 10x faster drilling speeds in rebar vs. 4-cutter drill bits. These rebar cutters are equipped with deep debris channels for the fastest rebar shard removal and double ejection slots for easy rebar slug removal. Each bit is designed with a 3-flat shank, providing users with better grip and control. Available in sizes 3/8” – 1-1/2”, Milwaukee Straight Shank Rebar Cutters are the optimal solution for drilling embedded rebar for corded and cordless ½" hammer drills/drivers. For use in rotation mode only. For use in rebar only.
