Irwin® Record® 5 Mechanics Vise, Replaceable Jaw, 6-1/2 in Jaw Opening, 5 in W Cast Iron Jaw, 3-1/4 in D Throat
Irwin® Record® vises are built to handle any job. The impressive, versatile line of vises from Irwin® is designed with the most sought-after features to fit every application, from the garage workbench to the factory floor. Whether used for cutting, screwing, drilling, planning, sanding or just holding, there is an Irwin® Record® vise that's perfect for the any type of holding application. Designed and manufactured to the highest standards and built with the best available materials, Irwin® Record® vises are available in a variety of styles, jaw widths, jaw capacities, base types and clamping forces. Refer to the chart below to select the best vise for the job.
-
BrandIrwin® Record®
-
UPC734442000723
-
Manufacturer Part Number5
-
CountryUSA
-
MaterialCast Iron
-
Throat Depth3-1/4 in
-
ColorBlue
-
Mounting TypeBolted-Down
-
Handle MaterialSteel
-
Handle TypeFused
-
Base TypeStationary
-
Jaw MaterialCast Iron
-
Jaw Opening6-1/2 in
-
Jaw TypeReplaceable
-
Jaw Width5 in
-
FinishBright
-
Point TypeSpeedPoint®
-
Maximum Hole Diameter1-3/8 in
-
Minimum Hole Diameter1/4 in
-
Applicable MaterialsAluminum/Brass/Copper/Laminates/Plastic/Stainless Steel
-
Number of Flutes1
-
Shank Size7/16 in
-
Cutting Edge MaterialHSS
-
Shank TypeHex
-
Number of Hole Sizes5
-
Number of Steps10
-
Drill Diameter Measurement SystemImperial
-
Step Depth1/8 in
-
Letter/Wire Size#5
-
TypeSelf-Starting
-
Overall Length3-1/16
- Replaceable hardened steel jaws
- Fused steel handle bends before vise can be overstressed
- Machined steel mainscrew with rolled two-start acme thread for wear resistance and smooth operation
- Fully machined on all load-bearing surfaces
- Internal SG nut takes load, secures and aligns mainscrew
- Can be replaced when worn, saving cost of replacement of whole vise body
- Safety stop prevents slide from accidentally separating from body
- Lip on back body guides filings and fragments away from the slide
- For machining straight surfaces
- <50 lb typical workpiece
| Competitor Name | Competitor Part Number |
|---|---|
| Fastenal | 99414626 |
| Fastenal | 99414626 |
-
UNSPSC27112102
-
Package Description1/PK
-
WarrantyLifetime
-
Catalog
Recently Viewed
Irwin® Record® 5 Mechanics Vise, Replaceable Jaw, 6-1/2 in Jaw Opening, 5 in W Cast Iron Jaw, 3-1/4 in D Throat
Irwin® Record® vises are built to handle any job. The impressive, versatile line of vises from Irwin® is designed with the most sought-after features to fit every application, from the garage workbench to the factory floor. Whether used for cutting, screwing, drilling, planning, sanding or just holding, there is an Irwin® Record® vise that's perfect for the any type of holding application. Designed and manufactured to the highest standards and built with the best available materials, Irwin® Record® vises are available in a variety of styles, jaw widths, jaw capacities, base types and clamping forces. Refer to the chart below to select the best vise for the job.
Black+Decker® DW5230 2-Cutter Premium Percussion Masonry Drill Bit, 3/8 in Drill Bit, 3/8 in 3-Flat Shank, 4 in D Cutting, Carbide Cutting Edge, 6 in OAL
Power through masonry, concrete, rock and more with DeWalt® hammer drill bits. Featuring Rock Carbide™ tips that maximize surface contact for extended bit life and a 4-flute design that cleans debris while you work. 3-flats on the shank eliminate bit slippage.
RIDGID® 41050 Handle Assembly With Nut, For Use With: Model BC-410/410P/410A/510/510A Bench Yoke Vise, Model 425/450/460/460-6/460-12 TRISTAND® Chain Vise, Model 560 Stand Chain Vise and Model 640 Post Chain Vise
RIDGID® 41050 Handle Assembly With Nut, For Use With: Model BC-410/410P/410A/510/510A Bench Yoke Vise, Model 425/450/460/460-6/460-12 TRISTAND® Chain Vise, Model 560 Stand Chain Vise and Model 640 Post Chain Vise
DeWALT® DW5416B25 Hammer Drill Bit, 1/4 in Drill Bit, 25/64 in SDS-Plus® Shank, 2 in D Cutting, Carbide Cutting Edge, 4 in OAL
DeWalt® Rock Carbide™ SDS Plus® hammer bit. Rock Carbide™ tip maximizes carbide surface contact for longer bit life. 4-flute design cleans debris out for fast, efficient drilling.
DeWALT® DW5417 Hammer Drill Bit, 1/4 in Drill Bit, 25/64 in SDS-Plus Shank, 4 in D Cutting, Carbide Cutting Edge, 16 in OAL
Featuring an innovative carbide tip for long bit life and a debris-cleaning U-flute, ULTRACON+ SDS Plus with 1/4 in. Hex Shank Masonry Drill Bits enable quick, efficient drilling. A hex shank interlocks with drive sleeves, enabling users to easily switch between drilling and driving.*
Porter-Cable® 43173 Router Bit, Classical Router, 1-1/2 in Dia Cutting, 2-21/64 in OAL, 1/4 in Dia Shank, Carbide
Porter-Cable® 43173 Router Bit, Classical Router, 1-1/2 in Dia Cutting, 2-21/64 in OAL, 1/4 in Dia Shank, Carbide
