Wilton® Brute Force™ 27211 O Series Extra Heavy Duty Standard Depth Throat C-Clamp, 4-1/4 in D Throat, 7 to 12-3/8 in Clamping, 7-1/2 to 12-1/2 in Jaw Opening, 1-1/8 in Screw
Wilton® Brute Force™ bridge c-clamps are ideal for heavy construction and fabrication. Brute force c-clamps boast a drop forged frame, black oxide coating and clamping pressure ranging up to 40,000 lbs. Spindles are full length, machined from a single piece of square, cold drawn steel tempered and hardened. Square spindle heads stand up to heavy wrench tightening.
-
BrandWilton®
-
UPC019907272113
-
Manufacturer Part Number27211
-
CountryUSA
-
Throat Depth4-1/4 in
-
Clamping Capacity7 to 12-3/8 in
-
Clamping Pressure40000 lb
-
TypeExtra Heavy Duty Standard Depth Throat
-
Screw Size1-1/8 in
-
SeriesO Series
-
Dimensions20.9 in L x 9.6 in W x 1.9 in H
-
Jaw Opening7-1/2 to 12-1/2 in
-
Body MaterialForged Steel
- The partial closing, extra heavy duty models are designed to stand up to the demands of heavy industrial applications like those encountered in ship building
- Hot upset square head on spindle withstands higher torque
- Square head spindle has large diameter rolled thread and hardened point which provides smoother operation and added strength
- Black oxide coated spindle resists corrosion
- Standard c-clamps are used for holding and aligning together multiple workpieces
-
Alternative Part Number12-SS
-
UNSPSC27112120
-
WarrantyLifetime
-
Catalog
Recently Viewed
Wilton® Brute Force™ bridge c-clamps are ideal for heavy construction and fabrication. Brute force c-clamps boast a drop forged frame, black oxide coating and clamping pressure ranging up to 40,000 lbs. Spindles are full length, machined from a single piece of square, cold drawn steel tempered and hardened. Square spindle heads stand up to heavy wrench tightening.
Heritage™ BP-233 Imperial Bridge Pin, 0.093 in Dia x 1-1/8 in L, Fits Shaft 1/4 to 1/2 in, MB Spring Wire, Zinc Clear
Heritage™ BP-233 Imperial Bridge Pin, 0.093 in Dia x 1-1/8 in L, Fits Shaft 1/4 to 1/2 in, MB Spring Wire, Zinc Clear
MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
IKO IRB2424 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 38.48 mm OAW, For Use With BA2824Z and BHA2824Z Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.
FYH® SA206 20FP7 SA Series Narrow Inner Ring Bearing Pillow Block Unit, 1-1/4 in Dia Bore, 1.18 in W, 19.5 kN Dynamic/11.3 kN Static Load
FYH® SA206 20FP7 SA Series Narrow Inner Ring Bearing Pillow Block Unit, 1-1/4 in Dia Bore, 1.18 in W, 19.5 kN Dynamic/11.3 kN Static Load
Sealmaster® gold ER bearings feature a cylindrical OD and snap ring for easy installation in a roll assembly. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction.

