Browning® 3749231 Taper Lock Bushing, 5/8 in Dia Bore, 2-3/4 in Dia Barrel, 1-1/4 in OAL, Steel
Browning® 3749231 Taper Lock Bushing, 5/8 in Dia Bore, 2-3/4 in Dia Barrel, 1-1/4 in OAL, Steel
-
BrandBrowning®
-
UPC662289614837
-
Manufacturer Part Number3749231
-
CountryUSA
-
Taper1-1/2 in/ft
-
MaterialSteel
-
Torque Rating7150 in-lb
-
Screw Size7/16 x 7/8 in
-
Number of Bolt Holes2
-
Barrel Diameter2-3/4 in
-
Keyway Size3/16 x 3/32 in
-
Bolt Circle Diameter2-5/8 in
-
Bore Diameter5/8 in
-
Overall Length1-1/4 in
-
Suitable For Use WithBrowning® Sprockets and HPT Chain Synchronous Belt Drives
-
Alternative Part Number2012X5/8
-
UNSPSC31163205
-
Package DescriptionEACH
-
Warranty1 Year
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Browning® 3749231 Taper Lock Bushing, 5/8 in Dia Bore, 2-3/4 in Dia Barrel, 1-1/4 in OAL, Steel
Browning® 3749231 Taper Lock Bushing, 5/8 in Dia Bore, 2-3/4 in Dia Barrel, 1-1/4 in OAL, Steel
Browning® 1296532 T55L Automatic Torque Limiter, 1-7/16 in Finished Bore, 5-1/2 in OD, 3800 in-lb (1-Spring)/6800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
Browning® 3748514 Taper Lock Bushing, 13/16 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3748514 Taper Lock Bushing, 13/16 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3750593 Taper Bore Bushing, 2-5/16 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL
Browning® 3750593 Taper Bore Bushing, 2-5/16 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL
ASP-752-S Industry Standard Clamping Collar, 2-Piece Construction, 3/4 in ID x 1-1/2 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
Moline Bearing 19341315 Type E Pillow Block Bearing, 3-15/16 in Dia Bore, 11-1/2 in L Bolt Center-to-Center, 4-1/4 in Base to Bore Centerline, 15-1/4 in OAL x 8-1/2 in OAH
Made of Cast Iron, this Solid Type E 4-Bolt Pillow Block is a Non-Expansion Mounted Roller Bearing Bearing with a 3 15⁄16 in (3.9375 in) shaft size. Includes a Steel Set Screw Locking Insert with a Double Collar, an available Standard V-Guard Contact Seal made of Nitrile, Teflon and Steel, and a Standard Painted finish, this bearing is ready for even the toughest of jobs.
