Browning® 3748480 Taper Lock Bushing, 5/8 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3748480 Taper Lock Bushing, 5/8 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
-
BrandBrowning®
-
UPC662289610914
-
Manufacturer Part Number3748480
-
CountryUSA
-
Taper1-1/2 in/ft
-
MaterialSteel
-
Torque Rating1300 in-lb
-
Screw Size1/4 x 1/2 in
-
Number of Bolt Holes2
-
Barrel Diameter1.511 in
-
Keyway Size3/16 x 3/32 in
-
Bolt Circle Diameter1-29/64 in
-
Bore Diameter5/8 in
-
Overall Length7/8 in
-
Suitable For Use WithBrowning® Sprockets and HPT Chain Synchronous Belt Drives
-
Alternative Part Number1108X5/8
-
UNSPSC31163205
-
Package DescriptionEACH
-
Warranty1 Year
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Browning® 3748480 Taper Lock Bushing, 5/8 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3748480 Taper Lock Bushing, 5/8 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3749231 Taper Lock Bushing, 5/8 in Dia Bore, 2-3/4 in Dia Barrel, 1-1/4 in OAL, Steel
Browning® 3749231 Taper Lock Bushing, 5/8 in Dia Bore, 2-3/4 in Dia Barrel, 1-1/4 in OAL, Steel
Browning® 1296532 T55L Automatic Torque Limiter, 1-7/16 in Finished Bore, 5-1/2 in OD, 3800 in-lb (1-Spring)/6800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
Browning® 3748514 Taper Lock Bushing, 13/16 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3748514 Taper Lock Bushing, 13/16 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3750593 Taper Bore Bushing, 2-5/16 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL
Browning® 3750593 Taper Bore Bushing, 2-5/16 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL
ASP-752-S Industry Standard Clamping Collar, 2-Piece Construction, 3/4 in ID x 1-1/2 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
