Browning® 3749462 Taper Lock Bushing, 1/2 in Dia Bore, 3-3/8 in Dia Barrel, 1-3/4 in OAL, Steel
Browning® 3749462 Taper Lock Bushing, 1/2 in Dia Bore, 3-3/8 in Dia Barrel, 1-3/4 in OAL, Steel
-
BrandBrowning®
-
UPC662289616589
-
Manufacturer Part Number3749462
-
CountryUSA
-
Taper1-1/2 in/ft
-
MaterialSteel
-
Torque Rating11600 in-lb
-
Screw Size1/2 x 1 in
-
Number of Bolt Holes2
-
Barrel Diameter3-3/8 in
-
Keyway Size1/8 x 1/16 in
-
Bolt Circle Diameter3-1/4 in
-
Bore Diameter1/2 in
-
Overall Length1-3/4 in
-
Suitable For Use WithBrowning® Sprockets and HPT Chain Synchronous Belt Drives
-
Alternative Part Number2517X1/2
-
UNSPSC31163205
-
Package DescriptionEACH
-
Warranty1 Year
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Browning® 3749462 Taper Lock Bushing, 1/2 in Dia Bore, 3-3/8 in Dia Barrel, 1-3/4 in OAL, Steel
Browning® 3749462 Taper Lock Bushing, 1/2 in Dia Bore, 3-3/8 in Dia Barrel, 1-3/4 in OAL, Steel
ASP-300-2-S Industry Standard Clamping Collar, 2-Piece Construction, 3 in ID x 4-1/4 in OD x 7/8 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
Browning® 3750197 Taper Bore Bushing, 1-13/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3750197 Taper Bore Bushing, 1-13/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3749900 Taper Lock Bushing, 1-9/16 in Dia Bore, 3-3/8 in Dia Barrel, 2-1/2 in OAL, Steel
Browning® 3749900 Taper Lock Bushing, 1-9/16 in Dia Bore, 3-3/8 in Dia Barrel, 2-1/2 in OAL, Steel
Crosby® 1031939 HG-227-1/2X6 Turnbuckle, Jaw/Eye, 1/2 in Thread, 2200 lb Working, 6 in Take Up, 14.48 in L Close, Steel
Crosby® 1031939 HG-227 Turnbuckle, Jaw/Eye, 1/2 in Thread, 2200 lb Working, 6 in Take Up, 14.48 in L Close, Steel
Drillco 76A112C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 3/16 in Dia Cutter, 5/8 in Length of Cut, 2 Flutes, 3/16 in Dia Shank, 2-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
