Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
-
BrandBrowning®
-
UPC662289617487
-
Manufacturer Part Number3750239
-
CountryUSA
-
Taper1-1/2 in/ft
-
Torque Rating24000 in-lb
-
Screw Size5/8 in Dia x 1-1/4 in L
-
Number of Bolt Holes2
-
Barrel Diameter4-1/4 in
-
Keyway Size1/2 x 1/4 in
-
Bolt Circle Diameter4 in
-
Bore Diameter2-1/16 in
-
Overall Length2 in
-
Suitable For Use WithGearbelt® Sprockets, HPT® and HPT Chain™ Synchronous Belt Drives
- Mounts flush in products - No protruding flanges to interfere with the drive
-
Alternative Part Number3020X 2 1/16
-
UNSPSC31163205
-
Package DescriptionEACH
-
Standards/ApprovalsABMA/AGMA/AIST/AWEA/CEMA/GEAPS/MPTA/NSSGA/PTDA Standards
-
Warranty1 Year
-
Instruction/Installation Manual
-
Catalog
-
Warranty Information
Recently Viewed
Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Drillco 76A120C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 5/16 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
Browning® 1296441 T45L Automatic Torque Limiter, 1-1/8 in Finished Bore, 4-1/2 in OD, 2800 in-lb (1-Spring)/4900 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
Moline Bearing 19321112 Type E Pillow Block Bearing, 1-3/4 in Dia Bore, 6-11/16 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8-7/8 in OAL x 4-1/2 in OAH
Made of Cast Iron, this Solid Type E 2-Bolt Pillow Block is a Non-Expansion Mounted Roller Bearing Bearing with a 1 3⁄4 in (1.7500 in) shaft size. Includes a Steel Set Screw Locking Insert with a Double Collar, an available Standard V-Guard Contact Seal made of Nitrile, and a Standard Painted finish, this bearing is ready for even the toughest of jobs.
CGW® 70121 Coated Abrasive Flap Disc, 4-1/2 in Dia, 120 Grit, Coarse Grade, Aluminum Oxide Abrasive, Type 29 Conical Disc
CGW® 70121 Coated Abrasive Flap Disc, 4-1/2 in Dia, 120 Grit, Coarse Grade, Aluminum Oxide Abrasive, Type 29 Conical Disc
SIZE 10/11 LARGE SHOE COVERS-WIK04 >
