Browning® Gearbelt® 3514007 Type BF Solid Synchronous Flanged Pulley, 1/2 to 2-5/8 in QD® Bore, 6.949 in OD, 44 Grooves, 7.003 in Dia Pitch, 1-13/16 in W Face
Browning® Gearbelt® 3514007 Type BF Solid Synchronous Flanged Pulley, 1/2 to 2-5/8 in QD® Bore, 6.949 in OD, 44 Grooves, 7.003 in Dia Pitch, 1-13/16 in W Face
-
BrandBrowning®
-
UPC662289352159
-
Manufacturer Part Number3514007
-
CountryUSA
-
Face Width1-13/16 in
-
Bushing TypeSK
-
Pitch1/2 in
-
Pitch Diameter7.003 in
-
MaterialCast Iron
-
Flange Diameter7-1/4 in
-
TypeType BF Solid
-
Number of Grooves44
-
Outside Diameter6.949 in
-
Bore Diameter1/2 to 2-5/8 in
-
Bore TypeQD®
-
Suitable For Use With1-1/2 in W Type H150 Belt
- Constant speed no slip, no creep, minimum backlash due to the positive engagement of the belt teeth with the grooves of the sprockets
- Light weight high horsepower to weight ratio makes Browning® Gearbelt® drives ideal for any application where weight is a factor
- Broad depth of product to choose from Browning® offers 5 different sprocket pitches along with a wide range of sprocket and belt widths to accommodate any horsepower requirement
- High modulus strength member, needs minimum take-up
- Freedom from initial belt tension, reduces bearing loads, increases life
- Compact design Gearbelt® belts permit smaller pulleys, shorter centers and narrow belts
- Less heat, because Gearbelt® drives generate virtually no friction
- No lubrication required
- Wide load capacity range
- Wide belt speed range
-
Alternative Part Number44H150SK
-
UNSPSC26111807
-
Package Description1/PK
-
Warranty1 Year
-
Catalog
-
Warranty Information
-
Instruction/Installation Manual
Recently Viewed
Browning® Gearbelt® 3514007 Type BF Solid Synchronous Flanged Pulley, 1/2 to 2-5/8 in QD® Bore, 6.949 in OD, 44 Grooves, 7.003 in Dia Pitch, 1-13/16 in W Face
Browning® Gearbelt® 3514007 Type BF Solid Synchronous Flanged Pulley, 1/2 to 2-5/8 in QD® Bore, 6.949 in OD, 44 Grooves, 7.003 in Dia Pitch, 1-13/16 in W Face
Browning® Gearbelt® 3513694 Type BF Solid Synchronous Flanged Pulley, 1/2 to 2-5/8 in QD® Bore, 5.357 in OD, 34 Grooves, 5.411 in Dia Pitch, 1-5/16 in W Face
Browning® Gearbelt® 3513694 Type BF Solid Synchronous Flanged Pulley, 1/2 to 2-5/8 in QD® Bore, 5.357 in OD, 34 Grooves, 5.411 in Dia Pitch, 1-5/16 in W Face
Browning® Gearbelt® 1057058 Type 4 Synchronous Timing Pulley With Flange, 3/8 to 1 in Split Taper Bore, 2.174 in OD, 14 Grooves, 2.228 in Dia Pitch, 1-3/4 in W Face
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
Tsubaki® BB30 Cam Clutch, 1.181 in Dia Bore, 2.441 in OD, 0.63 in W, 103.3 ft-lb Load
BB series cam clutches are a combination of a 62 series ball bearing and a cam style clutch. These units are designed for press fit applications and are available in five variations, combinations of metal shield or dust protective sealed type and with or without keyways on the inner and/or outer race to allow design and application flexibility. BB series units come grease lubricated but metal shielded style can be adapted for oil bath lubrication.
MasterDrive L075-20MM L075 Standard Jaw Coupling, 20 mm Dia Bore, 0.82 in L Through Bore, 1.75 in Dia Hub, Powdered Metal
Jaw Couplings provide standard shaft-to-shaft connection for general duty applications. Two hubs are used in pair with an elastomer or bronze element (spider), each sold seperately. The element eliminates metal-to-metal contact and acts as a shock absorber. The design is fail-safe in that it will perform if the element fails.
Browning® Gearbelt® 3513017 Solid Type EF Synchronous Timing Pulley With Flange, 1/2 to 1-1/4 in QD® Bore, 2.357 in OD, 20 Grooves, 2.387 in Dia Pitch, 3/4 in W Face
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
