TL-24-H-200-2012 Dodge® 113712 Dyna-Sync Type KF1 Timing Belt Pulley, 1/2 to 2 in Taper-Lock® Bore, 4.06 in OD, 24 Grooves, 3.82 in Dia Pitch, 2.34 in W Face
TL24H200-2012 Dodge® 113712 Dyna-Sync Type KF1 Timing Belt Pulley, 1/2 to 2 in Taper-Lock® Bore, 4.06 in OD, 24 Grooves, 3.82 in Dia Pitch, 2.34 in W Face
-
BrandDodge®
-
UPC782475088638
-
Manufacturer Part Number113712
-
CountryUSA
-
Face Width2.34 in
-
Bushing Type2012
-
Pitch1/2 in
-
Pitch Diameter3.82 in
-
Flange Diameter4.06 in
-
TypeDyna-Sync Type KF1
-
Hub Projection0.55 in
-
Number of Grooves24
-
Outside Diameter4.06 in
-
Bore Diameter1/2 to 2 in
-
Bore TypeTaper-Lock®
- Synchronized and no-slip transmission
- No lubrication required
- Approximately 98% efficiency can obtained
- Low maintenance
- Virtually no backlash
- Constant linear velocity
- 8.5:1 drive ratio
- Easy On/Off operation
- Flange design standard on drive size
-
Alternative Part NumberTL24H200-2012
-
UNSPSC26111807
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
TL-24-H-200-2012 Dodge® 113712 Dyna-Sync Type KF1 Timing Belt Pulley, 1/2 to 2 in Taper-Lock® Bore, 4.06 in OD, 24 Grooves, 3.82 in Dia Pitch, 2.34 in W Face
TL24H200-2012 Dodge® 113712 Dyna-Sync Type KF1 Timing Belt Pulley, 1/2 to 2 in Taper-Lock® Bore, 4.06 in OD, 24 Grooves, 3.82 in Dia Pitch, 2.34 in W Face
Coilhose® 624-S 600 Blow Gun, Extended Safety Tip, 150 psi Working, 24 in L Tube, 1/4 in FNPT Inlet x 1/8 in FNPT Outlet Thread, Die Cast Zinc, Domestic
The 600 series blow guns are a thumb lever style blow gun with an ergonomic shape and accept all Coilhose® 1/8 in tips. User comfort was designed into the 600 series with the elimination of the valve where the user's fingers are placed. Models that are designated as "safety" conform to OSHA standards for noise levels (1910.95) and 30 psi dead end pressure (1910.242B).
HCI Preferred Supplier 36220 4-Jaw Grease Gun Coupler, 1/8 in NPTF Thread, 1-1/2 in OAL, Steel
HCI Preferred Supplier 36220 4-Jaw Grease Gun Coupler, 1/8 in NPTF Thread, 1-1/2 in OAL, Steel
Browning® 767798 VF2E 100 Intermediate Duty Non-Expansion Flange Mount Ball Bearing Unit, 1-3/8 in Dia Bore, 5-1/8 in L Bolt Center-to-Center, 2-Bolt Flange Mount, 3-5/8 in OAL/Dia
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric or BOA concentric locking collar. The contact seal with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction.
Browning® 767779 VF2E 100 Intermediate Duty Non-Expansion Flange Mount Ball Bearing Unit, 1 in Dia Bore, 3-57/64 in L Bolt Center-to-Center, 2-Bolt Flange Mount, 2-3/4 in OAL/Dia
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric or BOA concentric locking collar. The contact seal with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction.
Sealmaster® gold mounted ball bearings feature wide outer race insert bearing with a land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system. This provides a direct path for lubrication into the bearing. It also helps prevent outer ring rotation. Available with either setscrew or Skwezloc®concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex®HP grease loss and friction.
