Gates® Power Transmission 1922V302 Bandless Multi-Speed V-Belt, 1-3/16 in W Top, 22 deg Groove, 30.8 in L Outside, Rubber
Power transmission systems do more than operate at constant speeds with constant outputs. Customers increasingly need variable speed systems to regulate the speed and rotational force, or output torque, of critical mechanical equipment. Our Multi-Speed belts are engineered for efficiency, energy savings and increased productivity at a wide range of speeds and speed ratios.
-
BrandGates® Power Transmission
-
UPC72053238822
-
Manufacturer Part Number1922V302
-
CountryUSA|Canada
-
MaterialRubber
-
Top Width1-3/16 in
-
Reinforced MaterialPolyester
-
TypeBandless
-
Groove Angle22 deg
-
Series9804
-
Outside Length30.8 in
- Notch design reduced thermal and bending stresses for longer life
- Smooth running construction for minimal vibration at high speeds
-
Alternative Part Number98040778
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission 1922V302 Bandless Multi-Speed V-Belt, 1-3/16 in W Top, 22 deg Groove, 30.8 in L Outside, Rubber
Power transmission systems do more than operate at constant speeds with constant outputs. Customers increasingly need variable speed systems to regulate the speed and rotational force, or output torque, of critical mechanical equipment. Our Multi-Speed belts are engineered for efficiency, energy savings and increased productivity at a wide range of speeds and speed ratios.
Simmons 904 Frost-Proof Yard Hydrant, 3/4 in, FNPT x Male Hose Thread, 4 ft Bury, Handle Shut-Off
The Simmons Sanitary Yard Hydrant is engineered to be fully self-contained and easily serviced in the field. It permits water flow year around, even in freezing weather, yet there is no ground contamination nor contamination of the water supply. This hydrant drains back into the stainless steel canister.
Wilton® Brute Force™ bridge c-clamps are ideal for heavy construction and fabrication. Brute force c-clamps boast a drop forged frame, black oxide coating and clamping pressure ranging up to 40,000 lbs. Spindles are full length, machined from a single piece of square, cold drawn steel tempered and hardened. Square spindle heads stand up to heavy wrench tightening.
Heritage™ BP-233 Imperial Bridge Pin, 0.093 in Dia x 1-1/8 in L, Fits Shaft 1/4 to 1/2 in, MB Spring Wire, Zinc Clear
Heritage™ BP-233 Imperial Bridge Pin, 0.093 in Dia x 1-1/8 in L, Fits Shaft 1/4 to 1/2 in, MB Spring Wire, Zinc Clear
MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
IKO IRB2424 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 38.48 mm OAW, For Use With BA2824Z and BHA2824Z Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.
