Gates® Power Transmission PowerGrip® GT®2 LL8MR30 Long Length Synchronous Belt, 30 mm W, 590 ft OAL, 8 mm Pitch, Neoprene
Long-length PowerGrip™ GT™2 belting is a cost effective, low maintenance drive alternative. The PowerGrip™ GT™2 belt tooth is designed for use with a specific sprocket groove profile. The sprocket groove-belt tooth combination increases capacity, while improving registration.
-
BrandGates® Power Transmission
-
UPC72053625639
-
Manufacturer Part NumberLL8MR30
-
CountryUSA|Canada
-
Pitch8 mm
-
Temperature Range-35 to 180 deg F
-
MaterialNeoprene
-
Tooth ProfileCurved
-
Reinforced MaterialFiberglass
-
TypeLong Length
-
Width30 mm
-
Series9396
-
Overall Length590 ft
- Fiberglass tensile cord provides high strength, excellent flex life and high resistance to elongation
- Nylon tooth facing provides a durable wear surface for long service life
- Eliminates lubrication and re-tensioning to reduce maintenance and labor as compared to roller chain drives
- Neoprene body provides protection against grime, grease, oil and moisture
- PowerGrip® GT®2 belt/sprocket combinations match or exceed the positional accuracy of PowerGrip® timing belt/pulley systems
- PowerGrip® GT®2 has more tooth ratchet resistance than HTD®
- The PowerGrip® GT®2 belt tooth is designed for use with a specific sprocket groove profile
- The sprocket groove-belt tooth combination increases capacity, while improving registration
- Long length PowerGrip® GT®2 belting is a cost effective, low maintenance drive alternative
-
Alternative Part Number93960030
-
UNSPSC26111811
-
Package DescriptionEACH
-
Standards/ApprovalsRMA Standard
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission PowerGrip® GT®2 LL8MR30 Long Length Synchronous Belt, 30 mm W, 590 ft OAL, 8 mm Pitch, Neoprene
Long-length PowerGrip™ GT™2 belting is a cost effective, low maintenance drive alternative. The PowerGrip™ GT™2 belt tooth is designed for use with a specific sprocket groove profile. The sprocket groove-belt tooth combination increases capacity, while improving registration.
Sealmaster 1-3/16" AIR HANDLING PILLOW BLOCKS SEA SPM-19-CXU
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
200-W 130-VOLT CLEAR BULBS
Crosby® 1043338 G-291-3/8 X 4 1/2 Eye Bolt With Regular Nut, 3/8 in, 4-1/2 in L Shank, Forged Steel, Hot Dipped Galvanized
Crosby® 1043338 G-291 Eye Bolt With Regular Nut, 3/8 in, 4-1/2 in L Shank, Forged Steel, Hot Dipped Galvanized
3" -FEMALE PIPE THREAD 45-DEGREE BLACK METAL ELBOW
MORSE® 90886 5951T Center Cutting Extra Long Length Single End End Mill, 1/2 in Dia Cutter, 3 in Length of Cut, 4 Flutes, 1/2 in Dia Shank, 6 in OAL, TiAlN Coated
