Gates® Power Transmission Poly Chain® GT® Carbon™ 14MGT-1568-37 Synchronous Belt, 37 mm W, 1568 mm OAL, 14 mm Pitch, 112 Teeth, Polyurethane
Give yourself a competitive advantage by designing in the Gates Poly Chain™ GT™ Carbon drive system instead of roller chain in your next power transmission application. The patented use of carbon fiber as the tensile cord in this belt provides increased horsepower rating for greater power density and compactness. When combined with Gates Poly Chain GT sprockets, you have a lightweight, long-lasting, maintenance-free system that's more than a match for roller chain.
-
BrandGates® Power Transmission
-
UPC72053451559
-
Manufacturer Part Number14MGT-1568-37
-
CountryUSA|Canada
-
Pitch14 mm
-
Temperature Range-65 to 185 deg F
-
MaterialPolyurethane
-
Tooth ProfileCurvilinear
-
Reinforced MaterialCarbon
-
Minimum Pulley Diameter139.81 mm
-
Width37 mm
-
Series9274
-
Number of Teeth112
-
Overall Length1568 mm
- Durable polyurethane construction resists chemicals, oil, pollutants and abrasion
- Nylon tooth facing reduces friction and eliminates the need for lubrication
- Maintenance-free, clean solution for roller chain drive conversion
- Significantly reduces maintenance cost
- Equivalent capacity to roller chain drives in the same width
- Easy rust-free wash-down with Gates® stainless steel hardware
- Fast drive conversion payback
- Quieter than roller chain drives
- New construction provides up to 55% more low-speed capacity than the original PCGT construction and 30% more than PCGT2
- Gates® curvilinear tooth profile provides high shear strength, noise reduction and improved load carrying capacity
- Robust carbon tensile cord combines minimal stretch with extraordinary strength and load carrying capacity, while absorbing shock and surge loads
-
Alternative Part Number92745112
-
UNSPSC26111811
-
Package DescriptionEACH
-
Standards/ApprovalsRMA Standard
-
Specification Sheet
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Poly Chain® GT® Carbon™ 14MGT-1568-37 Synchronous Belt, 37 mm W, 1568 mm OAL, 14 mm Pitch, 112 Teeth, Polyurethane
Give yourself a competitive advantage by designing in the Gates Poly Chain™ GT™ Carbon drive system instead of roller chain in your next power transmission application. The patented use of carbon fiber as the tensile cord in this belt provides increased horsepower rating for greater power density and compactness. When combined with Gates Poly Chain GT sprockets, you have a lightweight, long-lasting, maintenance-free system that's more than a match for roller chain.
Krylon® Quik-Mark™ K07095 Extra Large Hand Held Spotter Marking Wand, 12 in OAL, For Use With Quik-Mark™ Marking Paints, Plastic/Steel
Midland Industries 80-002 Dry Standard Pressure Gauge, 0 to 30 psi, 1/4 in Connection, 2 in Dial
Sealmaster® 700394 SEHB Non-Expansion Standard-Duty Hanger Ball Bearing Unit, 1-1/4 in Dia Bore, 3-5/8 in OD, 1-11/16 in W, Cast Iron Bearing, Set Screw Collar Locking
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
1-3/8" X 6' GOLD CARPET JOINING BAR-JWH260843>
