Dodge® 136252 209 Non-Expansion Normal Duty Wide Slot Take-Up Adapter Ball Bearing, 45 mm Dia Bore, 143 mm L x 120.7 mm H, 7891 lb Dynamic/4906 lb Static Load
Dodge® proudly presents a totally different ball bearing with a name that says it all Grip-Tight®. With its pull/push adapter system, fully concentric 360 deg inner ring, and completely interchangeable housing design, the new Dodge® Grip-Tight® ball bearing is the easy-on/easy-off solution for damage-free shafting, reduced vibration and greater cost/inventory savings. The Grip-Tight® ball bearing is shaft-ready right out of the box and offered in a variety of housing styles for normal and medium duty operations. It accommodates commercial grade and some undersized shafting to lower costs, and all Grip-Tight® assemblies fit into a standard Dodge® ball bearing housing. Plus, this Dodge® bearing has been specifically engineered to run at higher speeds and operate cooler for longer grease life. In test comparisons, the Dodge® Grip-Tight® bearing even proved it could suppress fretting corrosion and scarring to shafts and journals, thus saving not only time but also labor and maintenance costs.
-
BrandDodge®
-
UPC782475989898
-
Manufacturer Part Number136252
-
CountryUSA
-
Load Capacity7891 lb Dynamic/4906 lb Static
-
TypeNon-Expansion Normal Duty Wide Slot
-
Height120.7 mm
-
Series209
-
Bearing MaterialSteel
-
Length143 mm
-
Bore Diameter45 mm
-
Suitable For Use WithWS400 Wide Slot Take-Up Frames
- Non-metallic retainer provides added strength
- Case-carburized inner ring ensures greater wear resistance and longer life
- DualGuard® seal with rubberized flingers protects by keeping lubricants in, contaminants out
- Locknut/inner-ring interface acts as bearing puller to ease disassembly
- Grade 10 balls
- Higher speed capability
- Self-aligning
- Cooler operation for longer grease life
- Full contact on shaft for better grip
- Easy-on/easy-off
| Competitor Name | Cross-Reference Number |
|---|---|
| Applied Industrial Technologies | 101014685 |
| Motion Industries | 03711689 |
-
Alternative Part NumberWSTU-GT-45M
-
UNSPSC31171504
-
Package DescriptionEACH
-
Standards/ApprovalsUL Listed
-
WarrantyLimited
-
Instruction/Installation Manual
-
Catalog
-
Warranty Information
-
Specification Sheet
Recently Viewed
Dodge® 136252 209 Non-Expansion Normal Duty Wide Slot Take-Up Adapter Ball Bearing, 45 mm Dia Bore, 143 mm L x 120.7 mm H, 7891 lb Dynamic/4906 lb Static Load
Dodge® proudly presents a totally different ball bearing with a name that says it all Grip-Tight®. With its pull/push adapter system, fully concentric 360 deg inner ring, and completely interchangeable housing design, the new Dodge® Grip-Tight® ball bearing is the easy-on/easy-off solution for damage-free shafting, reduced vibration and greater cost/inventory savings. The Grip-Tight® ball bearing is shaft-ready right out of the box and offered in a variety of housing styles for normal and medium duty operations. It accommodates commercial grade and some undersized shafting to lower costs, and all Grip-Tight® assemblies fit into a standard Dodge® ball bearing housing. Plus, this Dodge® bearing has been specifically engineered to run at higher speeds and operate cooler for longer grease life. In test comparisons, the Dodge® Grip-Tight® bearing even proved it could suppress fretting corrosion and scarring to shafts and journals, thus saving not only time but also labor and maintenance costs.
ALUMINUM DIAMOND PLATE EXTRA WIDE CROSS BOX -WTG114001 >
BBI 693618 Teks® Fully Threaded Self-Drilling Screw, 1/4-14, 3 in OAL, Flat Head, Phillips® Drive, Low Carbon Steel, Zinc CR+3, Drill Point
BBI 693618 Teks® Fully Threaded Self-Drilling Screw, 1/4-14, 3 in OAL, Flat Head, Phillips® Drive, Low Carbon Steel, Zinc CR+3, Drill Point
MARXBORE™ 80699 384 Heavy Duty Jobber Length Drill Bit, #55 Drill - Wire, 0.052 in Drill - Decimal Inch, 135 deg Point, HSS, Black/Gold Oxide
The Square D™ by Schneider Electric brand heavy duty safety switch is designed to be tough, reliable and provide exceptional performance in the most gruelling conditions from commercial and institutional to industrial and manufacturing facilities. F Series safety switches provide significantly higher levels of mechanical endurance than NEMA KS-1 or UL98 standards require. The design life of a F Series switch is a minimum of three times the NEMA requirement. An abundance of copper is used in the heaviest current carrying power paths of all Square D™ by Schneider Electric heavy duty safety switches. The more copper for current carrying paths, the lower the temperature rise. Managing temperatures inside the switch is the key to providing greater service life. All heavy duty safety switches feature a quick-make, quick-break operating mechanism, a dual cover interlock and a color coded indicator handle.
#2 DRILLBIT-REP300F2>
