McGill 1"-ID NEEDLE BEARINGS MCG MR-16-N
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
-
BrandMcGill®
-
UPC726166065461
-
Manufacturer Part Number5451660000
-
CountryUSA
-
Load Capacity5840 lb Dynamic/7100 lb Static
-
Cage MaterialSteel
-
Temperature Rating-20 to 250 deg F
-
Maximum Speed12000 rpm
-
Closure TypeUnsealed
-
TypeHeavy Duty Narrow
-
Width3/4 in
-
SeriesMR Series
-
Number of Rows1
-
Bearing Material52100 Steel
-
Outside Diameter1-1/2 in
-
Bore Diameter1 in
- Machined outer race
- Needle roller with end relief
- Annular lubrication groove and holes
- Factory grease fill
- Narrow width
-
Alternative Part NumberMR 16 N
-
UNSPSC31171542
-
Package DescriptionEACH
-
Specification Sheet
-
Catalog
Recently Viewed
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
Campbell® T7645006 Spring Snap Link, 80 lb Load, 1/4 in Snap, 0.32 in Eye, 1.93 in OAL, Steel
Campbell® can trace its beginnings back to 1834, when one of the many companies that eventually became what is today the Campbell® brand began manufacturing harnesses for horses. Over the years, countless products were added, including wire rope and chain fittings, drop forged chain hardware, high quality tackle blocks, shackles, hooks and much more.
Conductor Range: 6 AWG to 250 kcmil (MCM) stranded copper wires. Stud/Bolt Size: 3/8-inch mounting hole. Drive Size: 1/4-inch internal hex main drive screw. Voltage & Temperature: Rated for up to 35 kV (with proper high-voltage insulation spacing techniques) and a maximum temperature of 90°C.Pre-Filled Compound: Contains DE-OX® oxide inhibitor to protect contact surfaces from corrosion. Certifications: UL 467 Listed (Grounding and Bonding), UL 486A/B Listed, and CS
V-BELTOUTSIDE CIRCUMFERENCE 68.6"-JAS1922V686 >
22-MM STUD TYPE CAM FOLLOWERS-INAKR22PP>
Southwire® Romex® SIMpull® 63950021 Type NM-B Sheathed Cable With Ground Wire, Coil Packaging, 600 V, (3) 6 AWG Stranded Copper Conductor, 25 ft L, Black
Southwire® Romex® Brand SIMpull ® NM-B (nonmetallic-sheathed) cable may be used for both exposed and concealed work in normally dry locations at temperatures not to exceed 90C (with ampacity limited to that for 60C conductors) as specified in the National Electrical Code. NM-B cable is primarily used in residential wiring as branch circuits for outlets, switches, and other loads. NM-B cable may be run in air voids of masonry block or tile walls where such walls are not wet or damp locations. Voltage rating for NM-B cable is 600 volts.
