Torrington 1-3/8"-ID NEEDLE BEARINGS TOR B-228
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearings are easily installed with a press fit in the housing.
-
BrandKoyo
-
UPC605790206757
-
Manufacturer Part NumberB-228
-
CountryUSA
-
Load Capacity4390 lbf Dynamic/9060 lbf Static
-
Temperature Rating250 deg F
-
Maximum Speed3200 rpm
-
Closure TypeOpen
-
TypeOpen Ends Uncaged
-
Width1/2 in
-
SeriesB Inch Series
-
Outside Diameter1-5/8 in
-
Bore Diameter1-3/8 in
- Full complement bearings handle high radial load-carrying capability
-
Alternative Part NumberB228PBL125
-
UNSPSC31171505
-
Standards/ApprovalsANSI/ABMA 18.2
-
Catalog
Recently Viewed
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearings are easily installed with a press fit in the housing.
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearings are easily installed with a press fit in the housing.
Browning® 3546991 TGC Cam Detent Mini Straight Bushing Overload Clutch, 1/2 in Dia Bore, 3.15 in OD, 23 to 56 in-lb Torque, 2.36 in OAL
The Browning® Torq/Gard® overload clutches are one of the most popular torque overload devices that power transmission solutions offers. A spring loaded cam follower seated in a single hub cam detent cause the hub and clutch to rotate together. Therefore, the clutch always resets in the same position if tripped, staying in phase. They can be turned in both directions by design. After tripping, the unit automatically resets when it returns to the set position. This is usually performed by jogging the machine after the jam or overload is cleared. Shaft bushings are used to accommodate a standard maximum bore unit to the application shaft requirement. Torque capacity up to 8000 in-lb and speed ranges from 350 to 1800 rpm.
PX-80-TL-2012 Dodge® Para-Flex® 10604 Type H Flange Assembly, 2-1/8 in Dia Bore, 8.38 in OD, 1-1/4 in L Through Bore, Cast Iron
Dodge® Para-Flex® 10604 Type H Flange Assembly, 2-1/8 in Dia Bore, 8.38 in OD, 1-1/4 in L Through Bore, Cast Iron
Sealmaster® 1441001000 3-Piece Precision Grade Extra Capacity Bearing Rod End With Zerk Grease Fitting, 5/8 in Dia Bore, 1-1/2 in OD, 3/4 in W, 17300 lb Static Load, Alloy Steel
Sealmaster® two and three piece rod end bearing housing designs have been optimized for overall strength. This housing advantage and variety of outer race materials including brass, steel, Delrin® and PTFE liners provide a wide selection of application solutions. Sealmaster® rod end bearings can be joined together or connected with a threaded rod or tube as linkage assemblies for flexibility in motion transfer. In addition Sealmaster® rod end bearings can accommodate angular misalignment to provide ease in assembly and smooth motion transfer in a variety of applications.
BBI 830120 Hex Bolt/Screw, M6x1, 30 mm L Under Head, A2-70 Grade, Stainless Steel
BBI 830120 Hex Bolt/Screw, M6x1, 30 mm L Under Head, A2-70 Grade, Stainless Steel
