Sealmaster 2"-ID 2-B HIGH BB PILLOW BLOCKS SEA NP-32-R
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461001738
-
Manufacturer Part Number700197
-
CountryUSA
-
Load Capacity7889 lb Dynamic
-
Locking DeviceSet Screw
-
Temperature Rating250 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed3550 rpm
-
TypeStandard-Duty
-
Mounting TypeTwo-Bolt Base
-
Seal TypeFelt
-
SeriesNP Series
-
Base Width2-3/8 in
-
Base to Bore Centerline2-1/4 in
-
Bolt Center-to-Center Length6 to 6-1/2 in
-
Bore Diameter2 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height4-9/16 in
-
Overall Length8-1/8 in
-
Overall Width2-1/32 in
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- High temperature synthetic grease
- Alemite fitting lubrication
- Powder coated epoxy cast iron housing with extended inner ring bearings
- Zone hardened inner ring with 120 deg spacing setscrew locking with diamond faceted setscrews
- Unique land riding retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- Sealmaster exclusive lock pin and dimple for direct lubrication and anti-rotation
| Competitor Name | Competitor Part Number |
|---|---|
| Grainger | 44A408 |
-
Alternative Part NumberNP-32R
-
UNSPSC31171504
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
12-MM X 1.50X30-MM HEX HEAD CAPSCREW-MET96112030F >
HCI Preferred Supplier 940801 Speed Control Valve, 1/4 in Port, 300 psi Pressure, 35 to 300 deg F
HCI Preferred Supplier 940801 Speed Control Valve, 1/4 in Port, 300 psi Pressure, 35 to 300 deg F
SEALS SMALL HOLES AND WEAK SEAMS IN GAS TANKS WITHOUT WELDING OR TANK REMOVAL. REPAIRS LEAKS AND HOLES IN ALL TYPES OF RADIATORS. NON-SHRINKING FORMULATION IS ETHANOL RESISTANT, HAS LONGER WORKING TIME, AND STAYS FLEXIBLE. AFTER FULL CURE, CAN BE MACHINED, TAPPED, DRILLED OR FILED. HARDENS IN 60 MINUTES. DRIES BROWN.
-JWH576415 >
Crosby® 1032796 HG-228 1 X 6 JJ Turnbuckle, Jaw/Jaw, 1 in Thread, 10000 lb Working, 6 in Take Up, 21.18 in L Close, Steel
Crosby® 1032796 HG-228 Turnbuckle, Jaw/Jaw, 1 in Thread, 10000 lb Working, 6 in Take Up, 21.18 in L Close, Steel
Weiler® 08155 ST-8 Heavy-Duty Wheel Brush, 8 in Dia Brush, 5/8 in W Face, 0.023 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 5/8 in Arbor Hole
Weiler® 08155 ST-8 Heavy-Duty Wheel Brush, 8 in Dia Brush, 5/8 in W Face, 0.023 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 5/8 in Arbor Hole
