Sealmaster 2-7/16"-ID M/D PILLOW BLOCK UNITS SEA SPM-39
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461008164
-
Manufacturer Part Number700989
-
CountryUSA
-
Load Capacity13971 lb Dynamic
-
Locking DeviceSet Screw
-
Temperature Rating-40 to 200 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed2500 rpm
-
TypeMedium Duty High Base
-
Mounting TypeTwo-Bolt Base
-
Seal TypeFelt
-
SeriesSPM
-
Base Width3 in
-
Base to Bore Centerline3-1/8 in
-
Bolt Center-to-Center Length7-7/8 to 9-3/8 in
-
Bore Diameter2-7/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height6-1/4 in
-
Overall Length11-1/2 in
-
Overall Width2-3/4 in
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- High temperature synthetic grease
- Alemite fitting lubrication
- Powder coated epoxy cast iron housing with extended inner ring bearings
- Zone hardened inner ring with 120 deg spacing setscrew locking with diamond faceted setscrews Air
- Handling noise check for quiet operation
- Looser than standard housing fit for ease of alignment on lightweight frames
- Felt labyrinth seal and flinger for dusty and dirty environment
- Unique land riding retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- Sealmaster exclusive lock pin and dimple for direct lubrication and anti-rotation
-
Alternative Part NumberSPM-39 CXU
-
UNSPSC31171504
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
he Crosby G-429 1/2" refers to the 1/2-inch Galvanized Fist Grip® Wire Rope Clip manufactured by Kito Crosby. Unlike traditional U-bolt style clips, this heavy-duty dual-saddle clamp features integral bolts and nuts that allow for rapid installation and eliminate the risk of installing the clip upside down
Deep Groove Ball Bearings (DGBB) are the most common form of rolling bearings and are used in a variety of applications, particularly those where high speeds and low power loss are required. NSK DGBB can handle not only radial forces, but also moderate axial loads in both directions. They are easy to install and can be deployed in a variety of configurations.
3/32" X 5/8" WOODRUFF KEY-MED1004 >
1/8" -FEMALE PIPE THREAD STAINLESS STEEL 45-D ELBOW-FIT1/8SS45 >
2-1/2" -FEMALE PIPE THREAD BLACK METAL TEE-FIT21/2BT >
