Sealmaster 2-3/16"-ID PILLOW BLOCK UNITS SEA SP-35-C
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461023341
-
Manufacturer Part Number703604
-
CountryUSA
-
Load Capacity9752 lb Dynamic
-
Locking DeviceSet Screw
-
Temperature Rating250 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed3250 rpm
-
TypeStandard-Duty
-
Mounting TypeTwo-Bolt Base
-
Seal TypeContact
-
SeriesSP Series
-
Base Width2-3/4 in
-
Base to Bore Centerline3-1/8 in
-
Bolt Center-to-Center Length7-5/8 to 9-3/8 in
-
Bore Diameter2-3/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height5-15/16 in
-
Overall Length11-1/4 in
-
Overall Width2-3/16 in
- Wide outer ring
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- GoldPlex®-HP grease
- Alemite fitting lubrication
- 52100 black oxide coated steel bearing
- Zone hardened inner ring with 120 deg spacing setscrew locking with diamond faceted setscrews
- Unique land riding retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- Sealmaster exclusive lock pin and dimple for direct lubrication and anti-rotation
-
Alternative Part NumberSP-35C
-
UNSPSC31171504
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
Gates® Power Transmission Hi-Power® II BB128 Banded Heavy Duty Double V-Belt, BB Section, 21/32 in W Top, 131 in L Outside, 17/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
MORSE® 44205 4552 Center Cutting Extra Long Length Single End End Mill, 5/8 in Dia Cutter, 4 in Length of Cut, 4 Flutes, 5/8 in Dia Shank, 6-1/8 in OAL, Bright
Gates® Power Transmission Hi-Power® II BB118 Banded Heavy Duty Double V-Belt, BB Section, 21/32 in W Top, 121 in L Outside, 17/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
Greenlee® 925-1-1/8 Ultra Hole Saw, 1-1/8 in Dia, 1/4 in D Cutting, Carbide Cutting Edge, 3/8 in Arbor
Greenlee® 925-1-1/8 Ultra Hole Saw, 1-1/8 in Dia, 1/4 in D Cutting, Carbide Cutting Edge, 3/8 in Arbor
10-MM-PITCH X 750-MM TIMING BELT - JAS25T10750>
