Sealmaster 2-3/16"-ID 2-BOLT BB PILLOW BLOCKS SEA MPD-35
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461016763
-
Manufacturer Part Number702305
-
CountryUSA
-
Load Capacity11789 lb Dynamic
-
Locking DeviceDouble Set Screw
-
Temperature Rating250 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed4100 rpm
-
TypeMedium Duty
-
Mounting TypeTwo-Bolt Base
-
Seal TypeFelt
-
SeriesMPD
-
Base Width3-1/8 in
-
Base to Bore Centerline2-3/4 in
-
Bolt Center-to-Center Length6-9/16 to 7-15/16 in
-
Bore Diameter2-3/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height5-5/8 in
-
Overall Length10-1/4 in
-
Overall Width3-1/8 in
- Wide outer ring
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- GoldPlex®-HP grease
- Alemite fitting lubrication
- 52100 black oxide coated steel bearing
- Powder coated epoxy cast iron housing with extended inner ring bearings
- Zone hardened inner ring with 120 deg spacing setscrew locking on both sides of ball path with diamond faceted setscrews
- Unique land riding retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- Sealmaster exclusive lock pin and dimple for direct lubrication and anti-rotation
-
Alternative Part NumberMPD-35
-
UNSPSC31171504
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
Diversitech 590-708 Variable Motor Start Capacitor, 590 to 708 uF, 110/125 V AC, Round
Diversitech 590-708 Variable Motor Start Capacitor, 590 to 708 uF, 110/125 VAC, Round
Browning® shear pin hubs are designed to prevent damage to machinery due to sudden overload or jamming by shearing the necked pin at a predetermined load. The inner part of the hub is keyed to the shaft and remains stationary while the outer part, to which the sprocket is bolted, rotates freely after pin breakage, allowing the drive to idle. Shear pin hubs are ideal for heavily lubricated areas where a cost effective solutions is needed.
2-1/2" -FEMALE PIPE THREAD STEEL GALVANIZED COUPLING-FIT21/2GSC >
Pyramex® CORDS Eyewear Retainer, 14 in L, Cotton/Polyester, Black
4X4" BLACK FRAME, GRAY LENS SAFETY GLASSES, STRONG, FOR-SIDED FRAME THAT WEIGHS JUST ONE-OUNCE, SOFT INSET NOSEPIECE PROVIDES A SECURE SNUG FIT-GSI41GB83 >
