Sealmaster 2-11/16"-ID H/DUTY PILLOW BLOCKS SEA SP-43
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461005101
-
Manufacturer Part Number700626
-
CountryUSA
-
Load Capacity13971 lb Dynamic
-
Locking DeviceSet Screw
-
Temperature Rating250 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed2500 rpm
-
TypeStandard-Duty
-
Mounting TypeTwo-Bolt Base
-
Seal TypeFelt
-
SeriesSP Series
-
Base Width3-3/8 in
-
Base to Bore Centerline3-3/4 in
-
Bolt Center-to-Center Length9-3/8 to 10-5/8 in
-
Bore Diameter2-11/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height7-1/8 in
-
Overall Length12-5/8 in
-
Overall Width2-3/4 in
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- High temperature synthetic grease
- Alemite fitting lubrication
- Powder coated epoxy cast iron housing with extended inner ring bearings
- Zone hardened inner ring with 120 deg spacing setscrew locking with diamond faceted setscrews
- Unique land riding retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- Sealmaster exclusive lock pin and dimple for direct lubrication and anti-rotation
-
Alternative Part NumberSP-43
-
UNSPSC31171504
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
The Crosby G-450 series refers to industry-standard, drop-forged galvanized wire rope clips distinguished by their signature Red U-Bolt®. Depending on whether you mean the 1-1/2" size (Crosby Stock #1010319) or the 1/2" size (Crosby Stock #1010131), the specific requirements for terminations vary significantly.
Gates® Power Transmission Hi-Power® II AA128 Banded Heavy Duty Double V-Belt, AA Section, 1/2 in W Top, 130 in L Outside, 13/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
Diversitech 161-193330 Variable Motor Start Capacitor, 161 to 193 uF, 330 V AC, Round
This DiversiTech® 161-193330 Motor Start Capacitor, 161-193µF, 330 volts motor start, electrolytic, non-polarized capacitor is designed for normal intermittent service on single-phase A/C motor starting circuits .
MEDIUM 35-MM 48 PVC & POLY RAINCOAT-BOO995630 >
RIDGID® 97457 VF6000 5-Layer Vacuum Filter, Green
