Sealmaster 1-15/16"-ID 4-BOLT PILLOW BLOCKS SEA MFP-31-C
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461026458
-
Manufacturer Part Number704179
-
CountryUSA
-
Load Capacity9752 lb Dynamic
-
Locking DeviceSet Screw
-
Temperature Rating250 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed3250 rpm
-
TypeMedium Duty
-
Mounting TypeFour-Bolt Base
-
Seal TypeSingle Lip
-
SeriesMFP-C
-
Base Width4 in
-
Base to Bore Centerline2-1/2 in
-
Bolt Center-to-Center Length6-3/8 to 7-5/8 in
-
Bore Diameter1-15/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height5-3/8 in
-
Overall Length9-3/4 in
-
Overall Width2-3/16 in
- Wide outer ring
- Lock pin and dimple
- Zone hardened inner race
- Land riding retainer
- Housing fit
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- Alemite fitting lubrication
- 52100 black oxide coated steel bearing
-
Alternative Part NumberMFP-31C
-
UNSPSC31171504
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
12-OZ AEROSOL FOAM SEALANT THAT EXPANDS 3" TIMES ORIGINAL VOLUME. CREATES AN AIRTIGHT, WATERPROOF SEAL WHERE GAPS ARE TOO LARGE FOR CAULK-JWH268976 >
1-1/2 -MALE PIPE THREADX2 STAINLESS STEEL NIPPLE
Dodge® Tigear-2® 20Q10R56 Standard Right Angle Worm Gear Speed Reducer, Quill Input, Solid B Shaft Output, 2.25 hp, 10:1 Gear, 175 rpm Maximum Output, 725 in-lb Torque Rating
The speed reducer shall be a single reduction worm gear reducer incorporating three input configurations - a quill style for direct attachment of electric motors, a separate keyed input shaft suitable for flexible coupling to a footed motor or belt and pulley input configuration and a motor adapter style input that employs a three piece coupling to connect electric motors to the reducer. These input configurations shall be available in both solid and hollow output shaft designs. The reducer shall be manufactured in the United States of America.
HYDRAULIC MALE PIPE FITTING-WHD10U112 >
3" X 2" COPPER SWEAT COUPLING-NIB600R3X2 >
