Sealmaster 1-1/2" 2-B LOW BB PILLOW BLOCKS SEA NPL-24-TC
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461033609
-
Manufacturer Part Number705880
-
CountryUSA
-
Load Capacity7340 lb Dynamic
-
Locking DeviceSkwezloc® Concentric Collar
-
Temperature Rating250 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed4150 rpm
-
TypeStandard-Duty
-
Mounting TypeTwo-Bolt Base
-
Seal TypeContact
-
SeriesNPL-T
-
Base Width2-1/8 in
-
Base to Bore Centerline1-15/16 in
-
Bolt Center-to-Center Length4-7/8 to 5-7/8 in
-
Bore Diameter1-1/2 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height3-15/16 in
-
Overall Length7-1/4 in
-
Overall Width2 in
- Wide outer ring
- Lock pin and dimple
- Zone hardened inner race
- Land riding retainer
- Housing fit
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- GoldPlex®-HP grease
- Alemite fitting lubrication
- 52100 black oxide coated steel insert
-
Alternative Part NumberNPL-24TC
-
UNSPSC31171504
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
20-MM-ID LOW PILLOW BLOCK UNIT-MBUUCPK20420MM >
Smith Bearing® CR-2-1/2-X Cylindrical Stud Type Needle Bearing Cam Follower, 2-1/2 in Dia x 1-1/2 in W Roller, 1 in Dia x 2-1/4 in L Stud, 52100 Steel Roller
Screwdriver slot stud type needle roller bearings are recommended where running loads and shock loads are moderate. Bearing capacity of the stud type series is limited by the moderately sized stud. Manufactured from high alloy bearing quality steel. Most commonly used general purpose cam follower and available in sealed versions.
Steel shim is made from a full hard, cold rolled, low carbon 1008-1010 steel. Precision Brand® is the only manufacturer to offer Branded® shim. It has everything the user needs to know clearly marked right on the shim: material type, material thickness and lot # for full traceability. Used in applications where hardness, flatness and accuracy are required. Material can be punched or sheared with minimum burring and distortion. Precision Brand® shim stock is widely used in the following applications: tool and die set up, alignment, new machine assembly, machine repair and maintenance; mounting of motors, pumps and other machines, short run and prototype work, along with a variety of other industrial uses. It is especially useful for pilot production runs where material accuracy and economy are important. All Precision Brand® shim products are manufactured under rigorous quality control standards to assure high accuracy and tight tolerances.
FYH® UCPX06 19 UCP Medium Duty Pillow Block Unit, 1-3/16 in Dia Bore, 5 in L Bolt Center-to-Center, 1-7/8 in Base to Bore Centerline, 1-7/8 in OAL 3-21/32 in OAH
FYH® UCPX06 19 UCP Medium Duty Pillow Block Unit, 1-3/16 in Dia Bore, 5 in L Bolt Center-to-Center, 1-7/8 in Base to Bore Centerline, 1-7/8 in OAL 3-21/32 in OAH
WaterWeld™ will plug or seal leaks and patch holes and cracks in almost anything. Ideal for repairing plumbing, fuel tanks, tub and shower, drains, pool and spa, boats and potable water tanks, setup occurs even under water. After curing, it can be drilled, tapped, filed, sanded and painted. WaterWeld™ has a set time of 15 to 25 min and sets hard in one hour. WaterWeld™ cures to an off white color, is rated at a tensile strength of 900 psi and will withstand temperatures up to 300 deg F.
