FYH® SB201 8KP8G5 SB Series Lightweight Pillow Block Unit, 5/8 in Dia Bore, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
FYH® SB201 8KP8G5 SB Series Lightweight Pillow Block Unit, 5/8 in Dia Bore, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
-
BrandFYH®
-
Manufacturer Part NumberSB201 8KP8G5
-
CountryUSA
-
Load Capacity9.55 kN Dynamic/4.8 kN Static
-
TypeLightweight
-
Width0.86 in
-
SeriesSB Series
-
Bore Diameter5/8 in
Recently Viewed
FYH® SB201 8KP8G5 SB Series Lightweight Pillow Block Unit, 5/8 in Dia Bore, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
FYH® SB201 8KP8G5 SB Series Lightweight Pillow Block Unit, 5/8 in Dia Bore, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
#14 X 5/8" Hex Head Slotted Sheet Metal Screws With Washer
Gardner Bender HST-250 Heat Shrink Tubing, 1/4 in ID Expanded, 1/8 in ID Recovered, 4 in L, Polyolefin, Black
Thin wall heat-shrink tubing is constructed from durable, flame-retardant black polyolefin which is resistant to both solvents and fluids making it ideal for cable insulation, repair, marking or bundling. Heat shrink not only provides superior mechanical, abrasion and moisture protection but also strengthens connections and provides a comfortable gripping surface. As a result, professional and DIY multi-purpose uses include repairing cords (ranging from large appliance cords to small electronic cables that show wear at pull-out), covering tool and sporting equipment handles, and sealing rope for neat, unravel resistant ends. Finally, tubing capably resists common fluids and solvents. Upon heating to 120 deg C (250 deg F) the tubing begins to shrink but will not drip, crack or flow and is self-extinguishing within 30 seconds. Meets UL 224, 125 deg C: CSA C22.2 No3 198.1, 125 deg C; MIL-DTL-23053/5, Class 1 and 2, AMS 3636 and 3637, DEF STAN 59-79, Issue 3 Type 2a. Continuous operating temperature: -55 deg C (-67 deg F) to 135 deg C (275 deg F). Shrink temperature: 120 deg C (250 deg F) to 250 deg C (480 deg F). 600 V/Mil Dielectric strength.
BBI 451168 Partially Threaded Cap Screw, 7/8-9, 10 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 451168 Partially Threaded Cap Screw, 7/8-9, 10 in L Under Head, 8 Grade, Alloy Steel, Plain
ISOSTATIC™ Oilube® 401045 Round Bore Sleeve Bearing, 1/4 in Dia Bore, 1/2 in OD, 1 in W
ISOSTATIC™ Oilube® 401045 Round Bore Sleeve Bearing, 1/4 in Dia Bore, 1/2 in OD, 1 in W
IKO LRB162016 Inch Series Inner Ring With Oil Groove, 1 in ID x 1-1/4 in OD, 25.65 mm OAW, For Use With BR202816 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
