FYH® SBB203 17MMKG5 SBB Cylindrical Ball Bearing Insert, 17 mm Dia Bore, 1.57 in OD, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
FYH® SBB203 17MMKG5 SBB Cylindrical Ball Bearing Insert, 17 mm Dia Bore, 1.57 in OD, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
-
BrandFYH®
-
Manufacturer Part NumberSBB203 17MMKG5
-
CountryUSA
-
Load Capacity9.55 kN Dynamic/4.8 kN Static
-
Closure TypeSetscrew Locking
-
TypeCylindrical
-
Width0.86 in
-
SeriesSBB
-
Outside Diameter1.57 in
-
Bore Diameter17 mm
Recently Viewed
FYH® SBB203 17MMKG5 SBB Cylindrical Ball Bearing Insert, 17 mm Dia Bore, 1.57 in OD, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
FYH® SBB203 17MMKG5 SBB Cylindrical Ball Bearing Insert, 17 mm Dia Bore, 1.57 in OD, 0.86 in W, 9.55 kN Dynamic/4.8 kN Static Load
Browning® PC9301 Waste Pack Kit
HCI Preferred Supplier 20081 90 deg Swivel Elbow, 1/4 in Nominal, Push-In x MNPTF End Style, Forged Brass
HCI Preferred Supplier 20081 90 deg Swivel Elbow, 1/4 in Nominal, Push-In x MNPTF End Style, Forged Brass
ISOSTATIC™ Oilube® 402236 Round Bore Flange Bearing, 5/8 in Dia Bore, 3/4 in OD, 5/8 in W, 1 in Dia Flange
ISOSTATIC™ Oilube® 402236 Round Bore Flange Bearing, 5/8 in Dia Bore, 3/4 in OD, 5/8 in W, 1 in Dia Flange
Browning® 1296482 T55L Automatic Torque Limiter, 1 in Finished Bore, 5-1/2 in OD, 3800 in-lb (1-Spring)/6800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
Coilhose® SC692502 Econolock Speed Control Elbow, For Use With: Pneumatic Actuators, 1/8 in MNPT Port, Brass
Coilhose's 90 deg speed controls are used to control the speed of pneumatic devices, such as air cylinders. These "free flow in/metered flow out" controls are adjustable via a knurled knob and feature a locking nut to retain the setting. Ideal for use directly on pneumatic actuators.
