Bearing Thrust Washers
Koyo TRD-2435 Thrust Washer, 38.1 mm ID x 55.55 mm OD, 3.2 mm W
Koyo TRC-2435 Double Direction Thrust Washer, 38.1 mm ID x 55.55 mm OD, 2.41 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Koyo TRC-2233 Double Direction Thrust Washer, 34.93 mm ID x 52.37 mm OD, 2.41 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Koyo TRB-2435 Double Direction Thrust Washer, 38.1 mm ID x 55.55 mm OD, 1.6 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Koyo TRA-1828 Double Direction Thrust Washer, 28.58 mm ID x 44.45 mm OD, 0.81 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Koyo TRA-1018 Double Direction Thrust Washer, 15.88 mm ID x 28.58 mm OD, 0.81 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
IKO AS1528 Thrust Washer, 15 mm ID x 28 mm OD, 1 mm W
Recently Viewed
RIDGID® 26463 Ground Stake, For Use With: Model ST-33Q Line Transmitter and ST-510 Base Assembly
RIDGID® 26463 Ground Stake, For Use With: Model ST-33Q Line Transmitter and ST-510 Base Assembly
BRAKE TOOLS-PEFW82004>
Apex® AM-4MM-4 Socket Head Bit, 1/4 in Hex Drive, 4 mm
ITM TR10030 Insert Set Screwdriver, 30 Pieces
Apex® AM-5MM-4 Socket Head Bit, 1/4 in Hex Drive, 5 mm
HARRINGTON ER2DS6241 Load Sheave Assembly, For Use With ER2/NER2 Series 010S/010L/020C Capacity Code Electric Chain Hoist
HARRINGTON ER2DS6241 Load Sheave Assembly, For Use With ER2/NER2 Series 010S/010L/020C Capacity Code Electric Chain Hoist
