Flex-Hone® BC5832 BC Series Small Diameter Standard Duty Flexible Cylinder Hone, 5/8 in Dia Bore, 2-1/2 in L Abrasive, 8 in OAL, 320 Grit
The BC Series Flex-Hone® tool is designed for use on any type or size of cylinder from 4 mm up to 3 in Dia. This cylinder hone is designed for surface finishing and cross hole deburring in brake cylinders, wheel cylinders, hydraulics, pneumatics and valve guides.
-
BrandFlex-Hone®
-
UPC843469128959
-
Manufacturer Part NumberBC5832
-
CountryUSA
-
Maximum Speed1200 rpm
-
TypeSmall Diameter Standard Duty
-
Grit320
-
Abrasive Length2-1/2 in
-
Abrasive MaterialSilicon Carbide
-
Applicable MaterialsMild Steel, Stainless Steel, Cast Iron, Softer Ferrous and Non-Ferrous Metals
-
SeriesBC Series
-
Bore Diameter5/8 in
-
Overall Length8 in
- Self centering, self aligning, self compensating for wear
- Can be used in virtually any rotating spindle
- Commonly used for finishing, deburring and edge breaking
- Typically achieves a finish of 18 to 30 Microinch (0.5 to 0.7 Micrometer)
| Competitor Name | Competitor Part Number |
|---|---|
| Berkshire eSupply | MJ73625320 |
| Berkshire eSupply | MJ73625320 |
-
UNSPSC31191500
-
Package DescriptionEACH
-
Standards/ApprovalsSGS Certified|PROP65: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov
-
Catalog
-
Technical Bulletin
Recently Viewed
Flex-Hone® BC5832 BC Series Small Diameter Standard Duty Flexible Cylinder Hone, 5/8 in Dia Bore, 2-1/2 in L Abrasive, 8 in OAL, 320 Grit
The BC Series Flex-Hone® tool is designed for use on any type or size of cylinder from 4 mm up to 3 in Dia. This cylinder hone is designed for surface finishing and cross hole deburring in brake cylinders, wheel cylinders, hydraulics, pneumatics and valve guides.
18/2" CLEAR LAMP CORD--250' ROLL-JWH548995 >
NACHI 7212B Angular Contact Ball Bearing, 60 mm Dia Bore, 110 mm OD, 1 Row, 22 mm W, 40 deg, 58000 N Dynamic/46000 N Static Load
The single-row angular contact ball bearing was designed to support radial, axial or composite loads, however, the axial load must be in one direction. The high thrust capacity is achieved by a higher shoulder on one side of the outer ring. A matching high shoulder is often on the opposite side of the inner ring as well. The direction of the load through the balls forms the contact angle. The thrust capacity increases with the contact angle. This ball bearing has a 40 deg contact angle. This bearing has a stamped steel cage and is not available with seals or shields. These bearings are non-separable. These bearings have normal tolerances and are not suitable for mounting adjacent to each other to achieve a preload.
Drillco 76A128C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 7/16 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 7/16 in Dia Shank, 2-3/4 in OAL, Bright
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
POSTS/PANELS-HLW50941807TAN>
Browning® 1296375 Automatic Torque Limiter, 3/4 in Straight Bore, 3-1/2 in OD, 1800 in-lb (1 Spring)/3000 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
