BRUSH RESEARCH BC3/4320SC BC Series Small Diameter Standard Duty Flexible Cylinder Hone, 3/4 in Dia Bore, 2-1/2 in L Abrasive, 8 in OAL, 320 Grit
The BC Series Flex-Hone® tool is designed for use on any type or size of cylinder from 4 mm up to 3 in Dia. This cylinder hone is designed for surface finishing and cross hole deburring in brake cylinders, wheel cylinders, hydraulics, pneumatics and valve guides.
-
BrandFlex-Hone®
-
UPC843469127358
-
Manufacturer Part NumberBC3432
-
CountryUSA
-
Maximum Speed1200 rpm
-
TypeSmall Diameter Standard Duty
-
Grit320
-
Abrasive Length2-1/2 in
-
Abrasive MaterialSilicon Carbide
-
Applicable MaterialsMild Steel, Stainless Steel, Cast Iron, Softer Ferrous and Non-Ferrous Metals
-
SeriesBC Series
-
Bore Diameter3/4 in
-
Overall Length8 in
- Self centering, self aligning, self compensating for wear
- Can be used in virtually any rotating spindle
- Commonly used for finishing, deburring and edge breaking
- Typically achieves a finish of 18 to 30 Microinch (0.5 to 0.7 Micrometer)
| Competitor Name | Competitor Part Number |
|---|---|
| Berkshire eSupply | MJ7375320 |
-
UNSPSC31191500
-
Package DescriptionEACH
-
Standards/ApprovalsSGS Certified|PROP65: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov
-
Catalog
-
Technical Bulletin
Recently Viewed
BRUSH RESEARCH BC3/4320SC BC Series Small Diameter Standard Duty Flexible Cylinder Hone, 3/4 in Dia Bore, 2-1/2 in L Abrasive, 8 in OAL, 320 Grit
The BC Series Flex-Hone® tool is designed for use on any type or size of cylinder from 4 mm up to 3 in Dia. This cylinder hone is designed for surface finishing and cross hole deburring in brake cylinders, wheel cylinders, hydraulics, pneumatics and valve guides.
ASP-622-S Industry Standard Clamping Collar, 2-Piece Construction, 5/8 in ID x 1-5/16 in OD x 7/16 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Power Team® P159 P-Series 2-Speed Manual Hydraulic Hand Pump, 152 cu-in Tank
Power Team® hand pumps, with the angled fill port, have a built in relief valve protection system. This system is designed to protect over pressurization of the reservoir from sudden back pressure. This system also works as a seal to prevent oil leaks.
1-1/2" STAINLESS STEEL 90 DEGREE WELD ELBOW-FIT11/2SSEWELD >
Browning® 3748878 Taper Lock Bushing, 3/4 in Dia Bore, 2-1/4 in Dia Barrel, 1 in OAL, Steel
