United Abrasives-SAIT 27320 Mounted Point, W204 Point, 3/4 in Dia x 3/4 in L Head, 1/4 in Dia Shank
United Abrasives-SAIT 27320 Mounted Point, W204 Point, 3/4 in Dia x 3/4 in L Head, 1/4 in Dia Shank
-
BrandUnited Abrasives-SAIT
-
UPC699053273204
-
Manufacturer Part Number27320
-
CountryUSA|Canada
-
Maximum Speed42750 rpm
-
GradeVery Fine
-
GritA60
-
Abrasive MaterialAluminum Oxide
-
Head Diameter3/4 in
-
Head Length3/4 in
-
Shank Diameter1/4 in
-
Shank Length1-1/2 in
-
Bond TypeVitrified Porous
-
Overall Length2-1/4 in
- These mounted bonded points are a low cost alternative to carbide burs
- Each point is dressed for perfect balance to perform without vibration or run out
- Mandrel overhang "O" must always be the lowest possible
- Maximum speeds given refer to overhang "O" equal to 1/2 in
- For use with die grinders
-
UNSPSC23131514
-
Package Description10/BX
-
Standards/ApprovalsOSHA 29 CFR 1910.1200
-
SDS
Recently Viewed
United Abrasives-SAIT 27320 Mounted Point, W204 Point, 3/4 in Dia x 3/4 in L Head, 1/4 in Dia Shank
United Abrasives-SAIT 27320 Mounted Point, W204 Point, 3/4 in Dia x 3/4 in L Head, 1/4 in Dia Shank
MORSE® 11663 1332B General Purpose Jobber Length Drill Bit, N Drill - Letter, 0.302 in Drill - Decimal Inch, 118 deg Point, HSS, Bright
MORSE® 11663 1332B General Purpose Jobber Length Drill Bit, N Drill - Letter, 0.302 in Drill - Decimal Inch, 118 deg Point, HSS, Bright
Milwaukee® 48-20-4138 2-Cutter Rotary Hammer Drill Bit, 1-3/8 in Drill Bit, 3/4 in Spline Shank, 16 in D Cutting, Carbide Cutting Edge, 22 in OAL
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
metabo® 676116000 2-Cutter Hammer Drill Bit, 1/2 in Drill Bit, Spline Shank, 11 in D Cutting, Carbide Cutting Edge, 16 in OAL
metabo® 676116000 2-Cutter Hammer Drill Bit, 1/2 in Drill Bit, Spline Shank, 11 in D Cutting, Carbide Cutting Edge, 16 in OAL
Drillco 700A015 Jobber Length Drill Bit, #15 Drill - Wire, 0.073 in Drill - Decimal Inch, 118 deg Point, Solid Carbide, Bright
700 series solid carbide drills retain hardness and sharp edges at high temperature. Their abrasion-resistant qualities make them advantageous for drilling abrasive materials. They offer the advantage of extreme rigidity for greater drilling accuracy.
MARXMANâ„¢ 85005 330QI General Purpose Jobber Length Drill Bit, 9/64 in Drill - Fraction, 0.1406 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MARXMANâ„¢ 85005 330QI General Purpose Jobber Length Drill Bit, 9/64 in Drill - Fraction, 0.1406 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
