Osborn Brush 1-1/2" CRIMPED WIRE BRASS BRUSHES OSB 11251

0 Ratings
$13.44
In Stock
SKU: OSB11251
noimage_new

Osborn 11251 Small Diameter Wheel Brush, 1-1/2 in Dia Brush, 7/32 in W Face, 0.005 in Dia Crimped Filament/Wire, 3/8 in Arbor Hole

In Stock
HCI of Jackson: 2
HCI of Dyersburg: 0
HCI of Humboldt: 0
HCI of Union City: 0
HCI of Gallatin: 0
My Wishlist
Compare
Main specs
  • Brand
    Osborn
  • UPC
    622424112512
  • Manufacturer Part Number
    0001125100
  • Country
    USA
Specification
  • Face Width
    7/32 in
  • Filament/Wire Diameter
    0.005 in
  • Filament/Wire Type
    Crimped
  • Fill Material
    Brass
  • Maximum Speed
    20000 rpm
  • Trim Length
    3/8 in
  • Type
    Small Diameter
  • Arbor Hole Size
    3/8 in
  • Attachment Type
    Unthreaded Arbor
  • Brush Diameter
    1-1/2 in
Features
  • Specially designed for effective brushing operations on internal surfaces and other hard-to-reach areas
  • Can be mounted, singly or in multiples, directly onto the shaft of a portable tool
Additional Information
  • UNSPSC
    31171805
  • Package Description
    12/PK
  • Standards/Approvals
    ANSI B165.1|ANSI B165.2
Attachments
Reviews

There are yet no reviews for this product.

Recently Viewed

Osborn 11251 Small Diameter Wheel Brush, 1-1/2 in Dia Brush, 7/32 in W Face, 0.005 in Dia Crimped Filament/Wire, 3/8 in Arbor Hole

The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.

Leviton® 13661-SNP Lampholder, 660 W Lamp, 600 VAC, Medium Bi-Pin Fluorescent Lamp

New
My Wishlist
Compare

Mounted Unit 1-3/4"-ID 2-BOLT TRB PILLOW BLOCKS MBU PBE-920 X 1-3/4

Pillow Block Roller Bearing Units
$512.23

Moline Bearing 19321112 Type E Pillow Block Bearing, 1-3/4 in Dia Bore, 6-11/16 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8-7/8 in OAL x 4-1/2 in OAH

The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.

Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.

If you need any additional information, prices, availability, etc. please contact us at 1-800-290-9908 or e-mail us at

Footer Menu