Gas Welder Fittings
FLARE CONNECTOR 1/2" OD TUBEX1/2" -MALE IPS-JWH414983 >
FLARE CONNECTOR 1/2" OD TUBEX3/4" -MALE IPS-JWH414992 >
FLARE CONNECTOR 5/8" OD TUBEX3/8" -MALE IPS-JWH415009 >
FLARE GAS CONNECTOR 5/8" OD TUBEX1/2" -MALE IPS-JWH415018 >
FLARE GAS CONNECTOR 5/8" OD TUBEX3/4" -MALE IPS-JWH415027 >
FLARE NUT BRASS CONNECTOR FITTING FOR 3/8" FLARE TUBE AND 9/16-24 FINE THREAD. SOLD IN BAG OF 5 PIECES-JWH419960 >
3/8"-TUBE X 1/2"FPT BRASS UNION-JWH419979>
FLARE MALE STRAIGHT BRASS CONNECTOR FITTING FOR 3/8" OD FLARE TUBE AND 9/16-24 FINE THREAD. 3/8" ODX3/8" . SOLD IN BAG OF 5 PIECES-JWH419988 >
FLARE MALE STRAIGHT BRASS CONNECTOR FITTING FOR 3/8" OD FLARE TUBE AND 9/16-24 FINE THREAD. 3/8" ODX1/2" . SOLD IN BAG OF 5 PIECES-JWH419997 >
FULL FLARE BRASS UNION CONNECTOR FITTING FOR 3/8" OD FLARE TUBE AND 9/16-24 FINE THREAD. SIZE 3/8" OD. SOLD IN BAG OF 5 PIECES-JWH420075 >
3/8"-MALE/TUBE X 3/8"-FPT ADAPTERS-JWH424909>
3/4" FPT X 5/8" TUBE GAS LINE FITTING-JWH429805>
3/8" COMP X 1/2" MPT CONNECTOR-JWH439056>
3/4" -MALE PIPE THREADX5/8" -OD GAS FITTING-JWH441739 >
1/2" MPT X 5/8"OD GAS LINE FITTINGS-JWH441748>
1/2" FX7/8" BRASS GAS FITTING-JWH441757 >
1/4" BRASS FLARE UNIONS-JWH443409>
3/8" BRASS FLARE UNIONS-JWH443522>
5/8" BRASS FLARE UNION-JWH443531>
5/8" BRASS FLARE UNION-JWH443531>
1/2" X 260" YELLOW TEFLON GAS TAPE-JWH445150 >
8-OZ TEFLON PASTE PIPE THREAD SEAL-JWH445177 >
1/2" X 1/2" FEMALE FLARE CONNECTOR-JWH445517>
1/2" TUBE X 3/4" FPT FLARE CONNECTOR-JWH445525>
Recently Viewed
Greenlee® 825-1-3/8 Variable Pitch Hole Saw, 1-3/8 in Dia, 1-5/8 in D Cutting, Bi-Metal Cutting Edge, 5/16 in, 7/16 in Arbor
Greenlee® 825-1-3/8 Variable Pitch Hole Saw, 1-3/8 in Dia, 1-5/8 in D Cutting, Bi-Metal Cutting Edge, 5/16 in, 7/16 in Arbor
1-QT NUWOOD NATURAL STAIN-BLP711QT>
1/2" Y" FITTING-PDTLV5551808 >
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
20-MM-ID LOW PILLOW BLOCK UNIT-MBUUCPK20420MM >
Smith Bearing® CR-2-1/2-X Cylindrical Stud Type Needle Bearing Cam Follower, 2-1/2 in Dia x 1-1/2 in W Roller, 1 in Dia x 2-1/4 in L Stud, 52100 Steel Roller
Screwdriver slot stud type needle roller bearings are recommended where running loads and shock loads are moderate. Bearing capacity of the stud type series is limited by the moderately sized stud. Manufactured from high alloy bearing quality steel. Most commonly used general purpose cam follower and available in sealed versions.
