A-B-C-D-E SHEAVES
2-GRV FINISHED BORE SHEAVE 1" BORE-BRW2BK32X1 >
2-GRV FINISHED BORE SHEAVE 1/2" BORE-BRW2BK32X1/2 >
2-GRV FINISHED BORE SHEAVE 3/4" BORE-BRW2BK32X3/4 >
2-GRV FINISHED BORE SHEAVE 7/8" BORE-BRW2BK32X7/8 >
2-GRV FINISHED BORE SHEAVE 1-1/8" BORE-BRW2BK34X11/8 >
2-GRV FINISHED BORE SHEAVE 5/8" BORE-BRW2BK34X5/8 >
2-GRV FINISHED BORE SHEAVE 7/8" BORE-BRW2BK34X7/8 >
2-GRV FINISHED BORE SHEAVE 1-1/8" BORE-BRW2BK36X11/8 >
2-GRV FINISHED BORE SHEAVE 1-3/8" BORE-BRW2BK36X13/8 >
2-GRV FINISHED BORE SHEAVE 3/4" BORE-BRW2BK36X3/4 >
Bushed Classical Gripbelt Sheave, 4L or A, 5L or B Belt, 2 Grooves, Uses H Bushing
Largest Selection of H Bushed sheaves of any other manufacturer - Browning offers bushed sheaves in both A & B Combination (A/B) configuration. 1, 2 & 3 Grooves are available to meet any fractional horsepower requirement.
Sheaves are Statically Balanced - All sheaves are statically balanced to assure smooth, vibration free performance.
Close Grain Cast iron - Close grain cast iron allows Browning to machine our sheaves to the closest tolerances possible.
Combination Groove - All Browning BK H Sheaves permit the running of A, 4L, B & 5L Belts to be run in them, thus providing a variety of different pitch diameters and horsepowers.
Type: Classical Gripbelt Sheave
Bore Size: 1 1/2
Bushing Used: H
Type of Bore: Bushed
V-Belt Pulley - 4L, 5L, A, B Belt Section, 2 Groove, 1 in Bore Size, 3.9500 in O.D., Finished Bore, Not Required Series Bushing, Cast Iron Material
2-GRV FINISHED BORE SHEAVE 1-1/8" BORE-BRW2BK40X11/8 >
2-GRV FINISHED BORE SHEAVE 7/8" BORE-BRW2BK40X7/8 >
2-GRV CAST IRON SHEAVE WITH SPLIT TAPER BUSHING 4.45" X 1-3/4"-BRW2BK47H >
2-GRV FINISHED BORE SHEAVE 1-3/8" BORE-BRW2BK52X13/8 >
2-GRV CAST IRON SHEAVE WITH SPLIT TAPER BUSHING 5.25" X 1-3/4"-BRW2BK55H >
2-BK-62-H 4 Groove Cast Iron Sheave With Split Taper Bushing 5.95" X 1-3/4"
4 GROOVE CAST IRON SHEAVE WITH SPLIT TAPER BUSHING 5.95" X 1-3/4"-BRW2BK62H >
2-BK-65-H 5 Groove Cast Iron Sheave With Split Taper Bushing 6.25" X 1-3/4"
5 GROOVE CAST IRON SHEAVE WITH SPLIT TAPER BUSHING 6.25" X 1-3/4"-BRW2BK65H >
2-GRV C-BELT QUICK DISCONNECT SF-BUSH SHEAVES-IDC2C110SF >
2 Groove C Belt Section Cast Iron Bushed Bore Multiple Sheave, QD Bushed, 8.4" Outside Diameter
2-GRV A-BELT H-BUSH SHEAVES
2-GRV A-BELT H-BUSH SHEAVES
2-GRV A-BELT H-BUSH SHEAVES
Recently Viewed
CARGO RATCHET STRAP WITH WIRE ENDS-RED802HD27W >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >69"-JASBX66 >
6_100x100.jpg)
ANTI-THEFT 5/8" RECEIVER HITCH PIN-JWH582186>
NOTCHED GRIP V-BELT 60."-JAS5VX600 >
579724 DO-IT-BEST/SAFETY VEHICLE EMBLEM 16" X 14" SLOW MOVING VEHICLE EMBLEM, DECAL
DURING DAYLIGHT, THE BRIGHT FLUORESCENT ORANGE SOLID TRIANGLE IN CENTER OF SMV EMBLEM IS HIGHLY VISIBLE. GAINS ATTENTIONAND RECOGNITION OF APPROACHING MOTORIST AT DISTANCES EXCEEDING 1/5 MILE.
-JWH579724 >
PIX 3-VX-450/02 COGGED WEDGE BANDED V-BELT. 3/8" X 45" OC, 43 " INSIDE LENGTH, 2 RIBS
MADE OF RUBBER CUSHION; POLYESTER CABLE CORD AS REINFORCEMENT AND RUBBER IMPREGNATED WOVEN COTTON-POLYESTER FABRIC. USED WHERE HORSE POWER CAPACITY OR OUTPUT IS NEEDED, WHEN SINGLE OR MULTIPLE DRIVES ARE IMPRACTICAL DUE TO LIMITED SPACE. USED WHERE BELT VIBRATION OR BELT WHIP CAUSES UNSATISFACTORY RESULTS WHERE MULTIPLE CONVENTIONAL V-BELTS ARE INSTALLED
-PIX3VX450/02>
