OIL SEALS
.787" X 1.378X.276 OIL SEAL-CHI7916 >
.787" X 1.260" X .276 OIL SEAL-CHI7918 >
.787" X 1.378X.315" OIL SEAL-CHI7926 >
OIL SEALS-.787" X 1.496" X .276"-CHI7930>
.787" X 1.575" X .276 OIL SEAL-CHI7940 >
.787" X 1.654" X .276 OIL SEAL-CHI7950 >
OIL SEALS-.787" X 1.890" X .276"CHI7970>
OIL SEALS-8.000" X 9.000" X .625"-CHI79960>
OIL SEALS-8.000" X 9.000" X .625"-CHI79998>
OIL SEALS-8.000" X 10.000" X .625"-CHI80038>
OIL SEALS-.813" X 1.250" X .188"-IMS8017>
.813" X 1.250" X .375" OIL SEALS-CHI8019 >
.813" X 1.375" X .375" OIL SEAL-CHI8053 >
.813" X 1.375" X .375" OIL SEAL-CHI8060 >
OIL SEALS-.813" X 1.375" X .234"-CHI8080>
.813" X 1.499" X .250" OIL SEAL - CHI8088>
8.000" X 9.250" X .625" OIL SEALS-TCM80926TA >
3.150" X 3.937" X .394" OIL SEALS-TCM80X100X10TC >
3.150" X 4.134" X .394" OIL SEALS-TCM80X105X10TC >
3.150" X 4.331" X .394" OIL SEALS-TCM80X110X10TC >
3.150" X 4.528" X .512" OIL SEALS-TCM80X115X13TC >
3.150" X 3.740" X .157" OIL SEALS-TCM80X95X4VAY >
OIL SEALS-.813" X 1.624" X .250"-CHI8178>
8.250" X 10.625" X .750" OIL SEALS-TCM821067TA >
Recently Viewed
TAPERED ROLLER BEARING CONE - NTN72188C>
1/4" X 5-1/2" USS Stainless Steel Hex Head Capscrew
TAPERED ROLLER BEARING CUP-NTN24720 >
7/8"-ID 4-BOLT FLANGE UNIT-GENUCF20514>
Gates® Power Transmission Hi-Power® II PowerBand® 2/B54 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 57 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Drillco 670A132B 6700A Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/2 in Dia Cutter, 1-1/4 in Length of Cut, 4 Flutes, 1/2 in Dia Shank, 3-1/4 in OAL, Uncoated
The greater red hardness of M-42 Cobalt end mills enables these tools to run about 10% faster than conventional HSS end mills. This translates to shorter machining times and permits higher utilization of available machine horsepower.
