TL-STYLE BUSHING
3020-2-5/8 2-5/8"-ID 3020-style Taper-lock Bushing
2-5/8"-ID 3020-STYLE TAPER-LOCK BUSHING - IDC302025/8>
30-MM-ID 3020-STYLE TAPER-LOCK BUSHING - IDC302030MM >
48-MM-ID 3020-STYLE TAPER-LOCK BUSHING - IDC302048MM>
60-MM-ID 3020-STYLE TL BUSHING - IDC302060MM>
1-1/2" ID 3020 STYLE TL-BUSHINGS-BRW3020X11/2>
1-1/8" -ID TAPER-LOCK BUSHING-BRW3020X11/8 >
1-1-1/16" -ID 3020-STYLE TAPER-LOCK BUSHING-BRW3020X111/16 >
1-13/16" -ID BUSHING-BRW3020X113/16 >
1-15/16" -ID BUSHING-BRW3020X115/16 >
1-3/4" -ID BUSHING-BRW3020X13/4 >
1-3/8" -ID BUSHING-BRW3020X13/8 >
1-5/8" -ID BUSHING-BRW3020X15/8 >
1-7/16" -ID BUSHING-BRW3020X17/16 >
1-7/8" -ID BUSHING-BRW3020X17/8 >
1-9/16" -ID BUSHING-BRW3020X19/16 >
1-1/16" -ID 3020-STYLE TAPER-LOCK BUSHING-BRW3020X1.1/16 >
1-3/16" -ID BUSHING-BRW3020X1.3/16 >
15/16" -ID BUSHING-BRW3020X15/16 >
2" -ID BUSHING-BRW3020X2 >
2-1/16" -ID BUSHING-BRW3020X21/16 >
2-1/2" -ID BUSHING-BRW3020X21/2 >
2-1/4" -ID BUSHING-BRW3020X21/4 >
2-1/8" -ID BUSHING-BRW3020X21/8 >
2-1-1/16" -ID BUSHING-BRW3020X211/16 >
Recently Viewed
15 TOOTH SPROCKETS FOR #40 CHAIN-BRWH4015X5/8 >
Fluke current clamps extend the current ranges of Fluke tools. The Fluke i1010 AC/DC current clamp is highly reliable, measures 1A to 1000A and provides accurate current reading without breaking the circuit. This clamp measures both ac and dc current with a large jaw, battery-powered Hall-effect probe that gives access to difficult to reach areas. Compatible with most Fluke multimeters.
Five ratcheting box wrenches packed in a vinyl 8-1/2-Inch x 10-Inch (21.6 x 25.4 cm) H roll-up pouch with individual pockets
Wrenches flip over to reverse ratchet
Set includes five double-hex wrenches with a different size at each end
Both ends are offset 25-degree for more convenient use in confined spaces and on long studs
Made in USA
Laminated construction for greater strength
Reverse ratcheting action by simply turning wrench over
Chrome-plated finish for rust resistance
1" SCH-80 SXS CPVC COUPLING-NIB1829010 >
1/2" -NATIONAL PIPE THREAD LOCKNUTS-DAY30610 >
Spherical roller bearing with relubrication features
Spherical roller bearings can accommodate heavy loads in both directions. They are self-aligning and accommodate misalignment and shaft deflections, with virtually no increase in friction or temperature. The design includes features to facilitate relubrication. The bearings can be used in a modular system, including housings, sleeves and nuts.
Accommodate misalignment
High load carrying capacity
Relubrication features
Low friction and long service life
Increased wear resistance
