Cordless Shears

The DEWALT DCS491B 20V max 18 gauge swivel head Shears features a 360 degree tool free swivel head which allows user to access tight quarters while maintaining comfort. Cuts 7/32" strips which continuously curls out of the cutting area providing consistent and accurate cuts. Cordless Shears allows user to take the tool to the work place. Specifications: capacity (stainless steel) - 20 gauge, capacity (mild steel) - 18 gauge, strokes/min - 0-2,300 SPD, min cutting Radius - 5.5 inches. Includes: (1) 20V max swivel head Shear bare tool. (Tool only / battery sold separately)

The DEWALT dcs496m2 20V max 18 gauge offset Shear features a tool-free 360 degree swivel head which allows user to access tight quarters while maintaining comfort. The offset Shear design can easily turn and cut circles. Also, this offset Shear design can easily cut through 20Ga spiral duct seams. Specifications: capacity in steel - 18 gauge, strokes/minute - 0-2,300 SPD, minimum cutting Radius - 1.0 inches. Includes: (1) Dcs496 Shear. (Tool only - battery sold separately).

The DEWALT DCS491M2 20V max 18 gauge swivel head Shears Kit features a 360 degree tool free swivel head which allows user to access tight quarters while maintaining comfort. Cuts 7/32" strips which continuously curls out of the cutting area providing consistent and accurate cuts. Cordless Shears allows user to take the tool to the work place. Specifications: capacity (stainless steel) - 20 gauge, capacity (mild steel) - 18 gauge, strokes/min - 0-2,300 SPD, min cutting Radius - 5.5 inches. Kit includes: (1) 20V max swivel head Shear, (2) 20V max 4.0Ah batteries, (1) DEWALT charger.

DeWALT® 18 ga shear attachment cuts up to 18 ga material including but not limited to: sheet metal, corrugated sheet metal, duct, asphalt shingles, steel mesh, vinyl siding, wire, plastics, cardboard and rubber.

The MILWAUKEE® M12™ Brushless Pruning Shears deliver the fastest, most controlled pruning while reducing fatigue. These pruning shears deliver the power to cut up to 1-1/4” branches while providing the ability to lock the blades into half of that capacity through the mode select board, increasing application speed by 40%. The M12™ Brushless Pruning Shears reduce muscle effort by 75% compared to manual solutions allowing users to complete tough applications with ease and speed. The Active Blade Control enables the blade movement to follow the trigger movement, providing more control over the cut capacity during application. This, combined with the mode select and lightweight, inline design, offers better accessibility and control in intricate pruning applications. When paired with the M12™ CP2.0 Battery, these pruning shears deliver up to 1,000 cuts per charge in ½” branches. The M12™ Brushless Pruning Shears are fully compatible with 150+ solutions within the M12™ system.

With the introduction of the new M18™ cordless shears, Milwaukee® has the most innovative and largest cordless shear selection on the market. By redesigning the body, we provide an in-line wrist design that maximizes control during use. Also adding the industry's only tool-free 360 deg rotating head our new shears can be used where hand snips have been needed to finish the cut. These innovations brought to each of the 3 new Milwaukee® cordless shears are changing the way tradesmen work on the jobsite today.

The MILWAUKEE® M12™ Plastic Pipe Shear cuts cleaner, faster, closer, and longer than traditional plastic pipe shears with over 200 cuts on one battery charge. The M12™ Plastic Pipe Shear can cut through 2” schedule 80 PVC in three seconds or less. Its razor-sharp pierce-point leaves pipe and tubing clean, burr-free, and ready for installation, minimizing the time spent on the job. Instantly open the jaw to increase productivity in repetitive cuts by using the tool’s quick blade release. Professionals can expect more work from this cordless shear with a 3mm stainless steel blade and aluminum jaw that resists impact, water, and rust. This Milwaukee pipe shear is powered by an M12™ REDLITHIUM Battery for more power and a longer run-time for maximum cuts per charge. The on-board battery fuel gauge helps monitor the charge status, so there’s less downtime on the job.

The MILWAUKEE® M18™ FORCE LOGIC™ Single Channel Strut Shear is the Most Productive Way to Shear Strut on the jobsite. Utilizing Milwaukee® proprietary Shearing Dies, the Strut Shear delivers square, clean shears without additional filing or deburring. The integrated strut support plate offers a quick 4in/10cm measurement offset for simple, repeatable shears increasing productivity on site. The Strut Shear’s dual die design eliminates exposed blades and reduces the chance of cut and laceration injuries on jobsites. This highly portable Strut Shear offers unmatched versatility allowing you to easily shear on any flat surface or chain vice at the point of installation around the jobsite. The integrated tri-stand chain vice mount allows seamless integration into any brand chain vice to keep users productive. Featuring Milwaukee® ONE-KEY™ Technology, view tool usage, receive notifications for recommended maintenance, and lock the tool out for added security to protect your investment. The kit includes (1) 1-5/8” x 1-5/8” Single Channel Shearing Dies, (1) M18™ XC 5.0 REDLITHIUM™ Battery, M18™ and M12™ Multi-Voltage Charger and a soft-sided carrying bag with pockets that can accommodate (3) additional Shearing Die Sets. Additional Accessory Dies available: 13/16” x 1-5/8” Dies (49-16-1316), 7/8” x 1-5/8” Dies (49-16-0078), Combination 13/16” & 1-5/8” Dies (49-16-1513), and Combination 7/8” & 1-5/8” Dies (49-16-1578).

With the introduction of the new M18™ cordless shears, Milwaukee® has the most innovative and largest cordless shear selection on the market. By redesigning the body, we provide an in-lbs wrist design that maximizes control during use. Also adding the industry’s only tool-free 360° rotating head, our new shears can be used where hand snips have been needed to finish the cut. These innovations brought to each of the 3 new Milwaukee® cordless shears are changing the way tradesmen work on the jobsite today.

With the introduction of the new M18™ cordless shears, Milwaukee® has the most innovative and largest cordless shear selection on the market. By redesigning the body, we provide an in-lbs wrist design that maximizes control during use. Also adding the industry’s only tool-free 360° rotating head, our new shears can be used where hand snips have been needed to finish the cut. These innovations brought to each of the 3 new Milwaukee® cordless shears are changing the way tradesmen work on the jobsite today.

With the introduction of the new M18™ cordless shears, Milwaukee® has the most innovative and largest cordless shear selection on the market. By redesigning the body, we provide an in-lbs wrist design that maximizes control during use. Also adding the industry’s only tool-free 360° rotating head, our new shears can be used where hand snips have been needed to finish the cut. These innovations brought to each of the 3 new Milwaukee® cordless shears are changing the way tradesmen work on the jobsite today.