Test Caps
2-1/2" FPT METAL GALVANIZED CAPS
2-1/2" -FEMALE PIPE THREAD METAL GALVANIZED CAP-FIT21/2GCA >
2-1/2" -FEMALE PIPE THREAD METAL BLACK CAP
2-1/2" -FEMALE PIPE THREAD BLACK METAL CAP-FIT21/2BCA >
2 BLACK METAL BUTT WELD CAP
2 -FEMALE PIPE THREAD STAINLESS STEEL CAP
2 -FEMALE PIPE THREAD SCHEDULE 80 METAL BLACK CAP
2 -FEMALE PIPE THREAD METAL GALVANIZED CAP
2 -FEMALE PIPE THREAD METAL BLACK CAP
2 -FEMALE PIPE THREAD 3000# METAL BLACK CAP
3/4" COPPER TUBE CAP-ELK1173/4 >
2" COPPER TUBE SWEAT CAPS-ELK1172>
1/2" COPPER TUBE CAP-ELK1171/2 >
1-1/4" COPPER TUBE CAP-ELK11711/4 >
1" COPPER TUBE CAP-ELK1171 >
1/8" STAINLESS STEEL CAP-FIT1/8SSCA >
1/8"-FPT METAL GALVANIZED CAPS
1/8" -MALE PIPE THREAD METAL GALVANIZED CAP-FIT1/8GCA >
1/8" -FEMALE PIPE THREAD 3000# BLACK CAP-FIT1/8BCA3000 >
1/8" -FEMALE PIPE THREAD BLACK CAP-JPW1/8BCA >
1/8" -FEMALE PIPE THREAD BLACK CAP-FIT1/8BCA >
1/4" -FEMALE PIPE THREAD STAINLESS STEEL CAP-FIT1/4SSCA >
1/4"-FPT METAL GALVANIZED CAPS
1/4" -FEMALE PIPE THREAD GALVANIZED CAP-FIT1/4GCA >
Recently Viewed
Inner Diameter (ID): 60 mm (2.36 inches) Outer Diameter (OD): 110 mm (4.33 inches) Width: 22 mm (0.87 inches) Load Rating: Basic dynamic load rating of 56.1 kN and basic static load rating of 42.5 kN Limiting Speed: Up to 6000 rpm (oil) or 6700 rpm Design: Utilizes filling slots to accommodate higher radial loads than standard deep groove bearings
14.4-V 4-GALLON BACKPACK SPRAYER-VALBPSREV401>
KEVLAR© IS A HIGH STRENGTH BELT THAT CAN WITHSTAND HIGHER SHOCK LOADS, REVERSE BENDING AND TWISTING OVER LONGER PERIODS OF TIME. THE STRENGTH COMES FROM THE CORDS, WHICH IS A HIGH TENSILE STRENGTH ARAMID FIBER. THESE BELTS USE A SPECIAL OUTER DRY WRAP, WHICH MAKES THEM SUITABLE FOR CLUTCHING APPLICATIONS, LAWN MOWERS OR ANY DRIVES WITH FREQUENT STARTING & STOPPING.
-PIXB112K>
OIL RESISTANT, ANTISTATIC, MAXIMUM BELT LINEAR SPEED UP TO 30M/SEC, INDUSTRIAL BELT TYPE, PRIMARILY USED AS REPLACEMENT ON INDUSTRIAL DRIVES. THE CLASSICAL BELTS ARE RECOMMENDED IN SPECIAL APPLICATIONS SUCH V-FLAT DRIVES . IN THE SAME MANNER THESE BELTS ARE ADVANTAGES WHERE REVERSE IDLERS HAVE TO BE USED BECAUSE OF SMALLER HEIGHTS.
-PIXA52K>
12 TOOTH SPROCKETS FOR #40 CHAIN-BRW40B12 >
2-AK-32X7/8 2-grv Cast Iron Sheave With Split Taper Bushing 7/8" Bore, Uses 4l Or A
2-GRV CAST IRON SHEAVE WITH SPLIT TAPER BUSHING 7/8" BORE, USES 4L OR A BELT-BRW2AK32X7/8 >
