Hose Preformed Clamps
HCI Preferred Supplier CP-06 Preformed Clamp, 1-1/2 in Nominal
HCI Preferred Supplier F10 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 2-1/2 in Nominal, 0.031 in THK
HCI Preferred Supplier F10 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 2-1/2 in Nominal, 0.031 in THK
HCI Preferred Supplier F12 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 3 in Nominal, 0.031 in THK
HCI Preferred Supplier F12 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 3 in Nominal, 0.031 in THK
HCI Preferred Supplier F14 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 3-1/2 in Nominal, 0.031 in THK
HCI Preferred Supplier F14 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 3-1/2 in Nominal, 0.031 in THK
HCI Preferred Supplier F20 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 5 in Nominal, 0.031 in THK
HCI Preferred Supplier F20 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 5 in Nominal, 0.031 in THK
HCI Preferred Supplier F24 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 6 in Nominal, 0.031 in THK
HCI Preferred Supplier F24 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 6 in Nominal, 0.031 in THK
HCI Preferred Supplier F3 Double Wrapped Triple Punched Preformed Hose Clamp, 13/16 in Nominal, 0.025 in THK
HCI Preferred Supplier F3 Double Wrapped Triple Punched Preformed Hose Clamp, 13/16 in Nominal, 0.025 in THK
HCI Preferred Supplier FS8 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 2 in Nominal, 0.022 in THK
HCI Preferred Supplier FS8 Double Wrapped Triple Punched Heavy Duty Preformed Hose Clamp, 2 in Nominal, 0.022 in THK
Recently Viewed
Dichtomatik N70404 O-Ring, 404 Dash Number, 1.85 in ID, Nitrile Rubber, 70 Shore A Durometer
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
ISOSTATICā¢ OilubeĀ® 401236 Round Bore Sleeve Bearing, 3/4 in Dia Bore, 15/16 in OD, 7/8 in W
ISOSTATICā¢ OilubeĀ® 401236 Round Bore Sleeve Bearing, 3/4 in Dia Bore, 15/16 in OD, 7/8 in W
StarrettĀ® 78XTZ-750 78XT Global SeriesĀ® Mechanical Bore Gage, 5/8 to 3/4 in, Graduations: 0.00025 in, 2-7/16 in D Probe, Tungsten Carbide
The Starrett 78XT Series Internal Micrometer features extended travel, reducing the need to exchange anvils. The ground contact points seat the internal micrometer faster and more accurately than the spherical contacts found in other gages. The rugged and accurate internal micrometer is available individually or in economical sets from .040-12" (1-300mm). 5/8-3/4" Range, w/3 Point Carbide Contact.
MakitaĀ® 792534-4 Center Blade, For Use With MakitaĀ® DJS161 Straight Shear
MakitaĀ® 792534-4 Center Blade, For Use With MakitaĀ® DJS161 Straight Shear
The LittelfuseĀ® LGR and LMF series fuses and LHR holder offer increased safety and reliability to lighting systems. on a 277 volt system, a fault occurring in an un-fused fixture could take out the entire branch circuit affecting upto 100 fixtures. this could cause safety problems as well as shut down operations. by individually fusing fixtures, these problems will be avoided. The added benefits of this is the ability to quickly identify the problem fixture and reduce the repair time. fuse holders are rated upto 10 A at 300 V and are equipped with 7 18 AWG leads. Order part number LHR 000 for two leads and part number LHR 001 for one lead and one terminal for insertion of 18 AWG ballast lead.
ISOSTATICā¢ OilubeĀ® 401177 Round Bore Sleeve Bearing, 9/16 in Dia Bore, 13/16 in OD, 1 in W
ISOSTATICā¢ OilubeĀ® 401177 Round Bore Sleeve Bearing, 9/16 in Dia Bore, 13/16 in OD, 1 in W
